Scopus İndeksli Yayınlar Koleksiyonu
Permanent URI for this collectionhttps://hdl.handle.net/20.500.12573/395
Browse
12 results
Search Results
Article Production of Waste-Based Lightweight Geopolymer Concretes Using Calcined Bentonite, Fly Ash, Slag, and Expanded Polystyrene Granules(Taylor & Francis Inc, 2026-03-19) Top, Soner; Nussrat Shukur Shukur, Yasir; Vapur, HüseyinThis study investigates the production of environmentally friendly lightweight geopolymer concretes utilizing fly ash (FA) as the primary precursor with calcined calcium bentonite (CCB), ferrochrome slag (SG), and expanded polystyrene (EPS) as supplementary components. A Box-Behnken design was employed to investigate the combined effects of CCB and SG additions, along with the solid-to-liquid ratio, on the compressive strength. Moderate CCB incorporation, particularly around 10%, improved mechanical performance, achieving strengths above 48 MPa, with a maximum of 51.33 MPa at 90 degrees C for a mix containing 5% CCB and 5% SG. Higher CCB dosages (>20%) reduced strength due to matrix dilution, while SG showed limited contribution at elevated levels. Incorporation of EPS granules reduced density to as low as 1292 kg/m & sup3;, yet compressive strengths between 25 and 30 MPa were maintained in mixes with 10% CCB and 0.3% EPS. SEM-EDX analysis confirmed dense geopolymer matrices in FA-CCB composites, whereas SG particles appeared less integrated. These results confirm the potential for producing high-strength, lightweight geopolymer concretes through the effective valorization of waste. The combined use of FA, CCB, SG, and EPS offers a sustainable pathway for resource-efficient construction that supports circular resource utilization.Article Sustainable Stabilization of Peat Soil with Hybrid Geopolymer Jet Grout Columns(Springer Int Publ A.G., 2025-10-15) Yalcin, Hakan; Erol, Aykut; Kaya, Zulkuf; Cadir, Cenk Cuma; Uncuoglu, Erdal; Akin, Muge K.Peat soils present severe challenges in geotechnical engineering due to their low shear strength, high water content, and aggressive chemical environments such as sulfate exposure. While cement-based jet grouting (JG) is widely used, it entails high carbon emissions and energy consumption. Hybrid geopolymer jet grout columns (HGJGCs) are presented in this work as a viable and sustainable alternative. Unlike conventional geopolymer studies that rely on pre-cured molds later exposed to aggressive environments, this research simulates realistic field conditions by injecting fresh geopolymer directly into sulfate-rich peat, where early-age durability and strength are critical. To address early strength limitations commonly seen in aggressive situations, a tiny amount of cement was added to the fly ash/GGBFS-based combination. Crucially, there is no need for high heat because the mechanism cures at room temperature. Physical model testing, laboratory-scale jet grouting, and performance comparisons with conventional JGCs were all carried out. Results show that HGJGCs increased the bearing capacity of peat by 5.5 times, improved compressive strength (5.3-5.7 MPa), and reduced settlement more effectively than JGCs. Additionally, CO2 emissions were reduced by 25.14% due to lower binder-related emissions and energy demand. This work shows that hybrid geopolymer systems are a viable, low-carbon substitute for peat stabilization because they can function well in real-world, chemically demanding situations.Article Citation - Scopus: 2Zeolite Synthesis by Alkali Fusion Method Using Two Different Fly Ashes Derived From Turkish Thermal Power Plants(Chamber of Mining Engineers of Turkey, 2020-03-01) Top, S.; Vapur, HüseyinIn this study, Faujasite (Na-LSX) (3.5(Ca0.3)3.5(Na0.6)3.5(Mg0.1)Al7Si17O48 32(H2O)) type zeolites and Ca-Filipsite (CaK0.6Na0.4Si5.2Al2.8O16 6(H2O)) type zeolites were produced from Sugözü Thermal Power Plant and Çatalaǧzi Thermal Power Plant fly ashes by alkali fusion method followed by water leaching, respectively. In these methods, fly ashes and sodium hydroxide (NaOH) were mixed in certain proportions and sintered at 600°C in ash furnace. Then, zeolites were obtained from the ground materials after water leaching and solid/liquid separation, respectively. Cation Exchange Capacity (CEC), X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Fourier-Transform Infrared Spectroscopy (FTIR), X-Ray Fluorescence (XRF) and Atomic Absorption Spectrometer (AAS) analyses were used to characterize the synthesized zeolites. The zeolites synthesized with Sugözü fly ashes in a ratio of 1:2 had 136.93 meq/100 g CEC, whereas the CEC of synthesized zeolite from Çatalaǧzi fly ashes was found to be 247.88 meq/100 g. As a result, zeolites, which can be used as wastewater treatment agent, energy storage material, catalyst and separator, were synthesized by using 2 different Class F fly ash. © 2023 Elsevier B.V., All rights reserved.Article Citation - WoS: 80Citation - Scopus: 90Properties of Fly Ash-Based Lightweight Geopolymer Concrete Prepared Using Pumice and Expanded Perlite as Aggregates(Elsevier, 2020-02) Top, Soner; Vapur, Huseyin; Altiner, Mahmut; Kaya, Dogan; Ekicibil, AhmetThe present paper aims to utilize the fly ash wastes with lightweight aggregates for geopolymer concrete production process in which sodium hydroxide (NaOH) and sodium metasilicate (Na2SiO3) were used as alkali activators, respectively. The designed experiments were examined by the Yates Analyses and so the productions of geopolymer concrete were investigated depending on curing temperature, solid/liquid rate and concentration of alkali activators. The curing temperature and alkali activator concentration were revealed as effective parameters in geopolymerization. The effects of expanded perlite (EP) and acidic pumice (AP) aggregates were discovered for the production of lightweight geopolymer concretes. The microstructural properties of each produced geopolymer concrete were characterized using SEM, EDS and laser particle size analyses. The specifications of the concrete were evaluated based on their uniaxial compressive strength (UCS), point load strength (PLS), sonic speed (SS), Mohs hardness (MH), and water absorption (WAR) ratio results. In addition, the effects of pre-wetting of EP aggregates, which have hydrophilic nature, were examined. To the best of our knowledge, this is the first time that pre-wetted lightweight EP aggregates were used to produce lightweight GP concretes. As a result of pre-wetting, chemical usage decreased by 32.5%. The UCSs of the lightweight geopolymer concretes were in a range of 10-50MPa and their unit weights changed between 1250 and 1700 kg/m(3). Lighter concretes were obtained by the addition of EP aggregates rather than AP ones. (C) 2019 Elsevier B.V. All rights reserved.Article Citation - WoS: 35Citation - Scopus: 29Microstructural Analysis of Low-Calcium Fly Ash-Based Geopolymer Concrete With Different Ratios of Activator and Binder Under High Temperatures(Springer Heidelberg, 2024-06-25) Kucukgoncu, Hurmet; Ozbayrak, AhmetGeopolymer concretes have emerged as an alternative to traditional Portland cement concretes with high strength, good durability, well corrosion performance and high-temperature resistance, and being a sustainable and environmentally friendly material. In this study, a comprehensive microstructural analysis of low-calcium fly ash-based geopolymer concrete samples with different alkali activator to binder ratios was conducted after exposure to temperatures ranging from 400 to 800 degrees C. The experimental results of the geopolymer concrete specimens found out significant findings, including a notable loss of mass and an approximate 80% decrease in compressive strength after exposure to 800 degrees C. The microstructural analysis underlined crack formation, voids and porosities in the geopolymer matrix at elevated temperatures, affecting the physical and mechanical properties of the material. The study presents significant insights into the behaviour of low-calcium fly ash-based geopolymer concrete with different binder and alkali activator ratios under high temperatures, revealing the performance of geopolymer concretes in extreme environments and the effect of incompatibility between geopolymer concrete and aggregate due to thermal temperature effects on this performance.Article Citation - WoS: 46Citation - Scopus: 52Life Cycle Assessment of Lightweight Concrete Containing Recycled Plastics and Fly Ash(Taylor & Francis Ltd, 2020-06-05) Ersan, Yusuf Cagatay; Gulcimen, Sedat; Imis, Tuba Nur; Saygin, Osman; Uzal, NigmetResearchers put significant effort to decrease the environmental impact of concrete by using industrial by-products as an alternative binder. However, the considerable environmental impact still exists due to the consumption of natural resources as aggregates. Natural aggregates are the most used resources by volume in the construction sector. Therefore, it is necessary to investigate by-products as an alternative to natural aggregates as well. This study presents the environmental impact of lightweight concrete (LWC) produced by replacing natural aggregates with recycled waste plastic (polyethylene) (RWP) and partially replacing Portland cement with Class F fly ash (FA). Life Cycle Assessment (LCA) was performed to compare a conventional LWC, containing pumice as natural aggregate and Portland cement as a binder, with green LWC, containing 30% RWP as pumice replacement and 20% FA as cement replacement. These scenarios were evaluated in terms of global warming potential, abiotic depletion, ozone layer depletion, terrestrial ecotoxicity, photochemical oxidation, acidification and eutrophication. LCA was coupled with mechanical tests at 7 days and 28 days. RWPs were found to be an environment-friendly replacement material for natural lightweight aggregates with an overall decrease in all CML-IA impacts except eutrophication. Tested green mix design also provided sufficient strength for nonstructural applications.Book Part Lead Blast Furnace Dust Recycling(Springer Science and Business Media Deutschland GmbH, 2023) Top, S.; Altiner, Mahmut; Kursunoglu, SaitThe recycling of lead (Pb), which has a limited reserve in the world, has great importance in terms of sustainable and efficient use of resources. Currently, more than half of the lead, which is the softest of base heavy metals, is recovered by recycling. In addition to the insulation of the cables and its use as a radiation shield, lead is mostly used in the manufacture of lead-acid batteries (LABs). Generally, lead smelting flue dust, also known as lead smelting fly ashes, formed during the smelting stage in secondary Pb production is fed back into the smelter. However, the impurities contained in this dust and the other required specifications for feeding into the furnace prevent dust from being fed back into the furnaces. Therefore, it is essential to evaluate these by-products with an effective process and to obtain valuable content from them. In this chapter, firstly the characterization of lead smelting flue dust has been investigated. Afterwards, the processes that can be applied to obtain contents such as Pb, Sb, Zn, and As from these materials were compiled from the literature and a comprehensive review study was presented. © 2023 Elsevier B.V., All rights reserved.Article Citation - WoS: 76Citation - Scopus: 81Influence of NaNo SiO2 and NaNo CaCo3 Particles on Strength, Workability, and Microstructural Properties of Fly Ash-Based Geopolymer(Ernst & Sohn, 2020-05-06) Durak, Ugur; Karahan, Okan; Uzal, Burak; Ilkentapar, Serhan; Atis, Cengiz DuranThe influence of nano SiO2(NS) and CaCO3(NC) particles on the properties of class F fly ash based geopolymer mortar activated with different sodium ion concentrations have been investigated. Mortar mixture proportions were 1:3:0.3 for binder, sand, and water, respectively. Nano SiO2 and CaCO3 particles were replaced with a binder by weight basis at the ratios of 1, 2, and 3% in the mixtures. Sodium concentrations amount used were 8, 10, and 12% Na+ of binder content. Geopolymer mortar samples were cured at 60, 75, and 90 degrees C in a furnace for 24, 48, and 72 hr. After the heat curing process, flexural, and compressive strength tests were performed. The changes in the microstructure of geopolymer due to influence of nanoparticles were examined by utilizing isothermal calorimetric studies on geopolymer paste, and field-emission scanning electron microscopy (FESEM). Based on laboratory work results, it was concluded that for all sodium ion concentrations, the addition of nano SiO2 and CaCO3 particles improved the flexural and compressive strengths after 24 hr heat curing. However, the favorable effects of nanoparticles on strength properties tend to disappear after 48 and 72 hr heat curing. The results of isothermal calorimetric studies showed that nano SiO2 and CaCO3 particles accelerated the geopolymeric reactions at an early age. FESEM results showed that additions of nanoparticles made the microstructure of geopolymer products more intense and compact.Article Citation - WoS: 7Citation - Scopus: 7Effect of Nano-SiO2 on Strength and Hydration Characteristics of Ternary Cementitious Systems(Springer Heidelberg, 2023-05-31) Yorulmaz, Hediye; Uzal, Burak; Karahan, Okan; Durak, Ugur; Ilkentapar, Serhan; Atis, Cengiz DuranThis paper shows results of laboratory study on the effects of nano-SiO2 on Portland cement-fly ash systems. It is aimed to improve performance of fly ash-cement systems, particularly at early age, with the inclusion of nano-SiO2. In order to observe the effects of nano-SiO2 particles on the strength and hydration kinetics of fly ash blended cementitious systems, binary and ternary systems were prepared by adding 0.25-1.5% nano-SiO2 by weight of blended cements. Workability, setting time, water absorption capacity, fire resistance, compressive strength and isothermal calorimeter tests were conducted on the cementitious systems. The results indicate that increasing quantity of fly ash increased workability, setting time, water absorption capacity of cementitious systems, whereas the increasing quantity of nano-SiO2 reduced these values. Significant increment in compressive strength were observed, especially at early ages of fly ash-cement systems with nano-SiO2 addition, compared to fly ash added systems, which may compensate for the decrease in compressive strength caused by fly ash. Nano-SiO2 addition accelerated hydration reactions at early age. By partially eliminating the negative effects of fly ash with nano-SiO2, high rates of fly ash can be used in cementitious systems, thus forming more sustainable systems.Article Citation - WoS: 77Citation - Scopus: 92Effect of Granulated Blast Furnace Slag and Fly Ash Addition on the Strength Properties of Lightweight Mortars Containing Waste PET Aggregates(Elsevier Sci Ltd, 2011-10) Akcaozoglu, Semiha; Atis, Cengiz Duran; Akaözolu, Semiha; Ati, Cengiz DuranIn this work, the effect of Granulated Blast Furnace Slag (GBFS) and fly ash (FA) addition on the strength properties of lightweight mortars containing waste Poly-ethylene Terephthalate (PET) bottle aggregates was investigated. Investigation was carried out on three groups of mortar specimens. One made with only Normal Portland cement (NPC) as binder, second made with NPC and GBFS together and, third made with NPC and FA together. The industrial wastes mentioned above were used as the replacement of cement on mass basis at the replacement ratio of 50%. The size of shredded PET granules used as aggregate for the preparation of mortar mixtures were between 0 and 4 mm. The waste lightweight PET aggregate (WPLA)-binder ratio (WPLA/b) was 0.60; the water-binder (w/b) ratios were determined as 0.45 and 0.50. The dry unit weight, compressive and flexural-tensile strengths, carbonation depths and drying shrinkage values were measured and presented. The results have shown that modifying GBFS had positive effects on the compressive strength and drying shrinkage values (after 90 days) of the WPLA mortars. However, FA substitution decreased compressive and flexural-tensile strengths and increased carbonation depths. Nevertheless a visible reduction occurred on the drying shrinkage values of FA modifying specimens more than cement specimens and GBFS modified specimens. The test results indicated that, GBFS has a potential of using as the replacement of cement on the WPLA mortars by taking into consideration the characteristics. But using FA as a binder at the replacement ratio of 50% did not improve the overall strength properties. Although it was thought that, using FA as binder at the replacement ratio of 50% for the aim of production WPLA concrete which has a specific strength, would provide advantages of economical and ecological aspects. (C) 2011 Elsevier Ltd. All rights reserved.