Scopus İndeksli Yayınlar Koleksiyonu
Permanent URI for this collectionhttps://hdl.handle.net/20.500.12573/395
Browse
4 results
Search Results
Article Structural Behavior of Geopolymer Reinforced Concrete Beams: Experimental, Numerical, and Code-Based Assessment(Springer, 2025-08-11) Ozbayrak, Ahmet; Kucukgoncu, HurmetThis study experimentally investigates the flexural performance of heat-cured low-calcium fly ash-based geopolymer concrete (GPC) beams reinforced with ribbed steel bars, focusing on the effects of reinforcement ratio, alkaline activator concentration (SS/SH), and curing regime. Fifteen full-scale beams, including twelve GPC and three OPC specimens, were tested under four-point loading to evaluate load-deflection and moment-curvature behavior. Despite a lower compressive elastic modulus, the results showed that GPC beams exhibited comparable or superior cracking and ultimate moment capacities relative to OPC beams. Increasing the reinforcement ratio enhanced load capacity but reduced ductility in both systems, with GPC beams showing more brittle post-yield behavior. Numerical models based on OPC parameters were developed in SAP2000 to compare with experimental GPC moment-curvature data, revealing good agreement in the linear range but notable differences in post-yield response. The study also examined the microstructure of failed GPC beams via SEM, XRD, and EDX analyses to correlate matrix morphology with mechanical behavior. Finally, moment capacities calculated according to ACI 318 and TS 500 provided conservative estimates, supporting the safe applicability of current design codes to heat-cured GPC beams. These findings demonstrate that GPC, when properly proportioned and cured, is a viable structural alternative to OPC for reinforced concrete members.Article Citation - WoS: 35Citation - Scopus: 29Microstructural Analysis of Low-Calcium Fly Ash-Based Geopolymer Concrete With Different Ratios of Activator and Binder Under High Temperatures(Springer Heidelberg, 2024-06-25) Kucukgoncu, Hurmet; Ozbayrak, AhmetGeopolymer concretes have emerged as an alternative to traditional Portland cement concretes with high strength, good durability, well corrosion performance and high-temperature resistance, and being a sustainable and environmentally friendly material. In this study, a comprehensive microstructural analysis of low-calcium fly ash-based geopolymer concrete samples with different alkali activator to binder ratios was conducted after exposure to temperatures ranging from 400 to 800 degrees C. The experimental results of the geopolymer concrete specimens found out significant findings, including a notable loss of mass and an approximate 80% decrease in compressive strength after exposure to 800 degrees C. The microstructural analysis underlined crack formation, voids and porosities in the geopolymer matrix at elevated temperatures, affecting the physical and mechanical properties of the material. The study presents significant insights into the behaviour of low-calcium fly ash-based geopolymer concrete with different binder and alkali activator ratios under high temperatures, revealing the performance of geopolymer concretes in extreme environments and the effect of incompatibility between geopolymer concrete and aggregate due to thermal temperature effects on this performance.Article Hydrogen Susceptibility of Al 5083 Under Ultra-High Strain Rate Ballistic Loading(Walter de Gruyter Gmbh, 2024-09-25) Baltacioglu, Mehmet Furkan; Mozafari, Farzin; Aydin, Murat; Cetin, Baris; Oktan, Aynur Didem; Teoman, Atanur; Bal, BurakThe effect of hydrogen on the ballistic performance of aluminum (Al) 5083H131 was examined both experimentally and numerically in this study. Ballistics tests were conducted at a 30 degrees obliquity in accordance with the ballistic test standard MIL-DTL-46027 K. The strike velocities of projectiles were ranged from 240 m s-1 to 500 m s-1 level in the room temperature. Electrochemical hydrogen charging method was utilized to introduce hydrogen into material. Chemical composition of material was analyzed using energy dispersive X-ray (EDX) analysis. Instant camera pictures were captured using high-speed camera to compare H-uncharged and H-charged specimen ballistics tests. The volume loss in partially penetrated specimens were assessed using the 3D laser scanning method. Microstructural examinations were conducted utilizing scanning electron microscopy (SEM). It was observed that with the increased deformation rate, the dominance of the HEDE mechanism over HELP became evident. Furthermore, the experimental findings were corroborated through numerical methods employing finite element analysis (FEM) along with the Johnson-Cook plasticity model and failure criteria. Inverse optimization technique was employed to implement and fine-tune the Johnson-Cook parameters for H-charged conditions. Upon comparing the experimental and numerical outcomes, a high degree of consistency was observed, indicating the effective performance of the model.Article Citation - WoS: 9Citation - Scopus: 11Evaluation of Diatomite Substitute With Thermal Power Plant Waste Fly Ash in Sustainable Geopolymer Through Life Cycle Assessment(Springer, 2025-02-28) Ilkentapar, Serhan; Orklemez, Ezgi; Durak, Ugur; Gulcimen, Sedat; Bayram, Savas; Uzal, Nigmet; Atis, Cengiz DuranThis research demonstrates the potential of diatomite as a fly ash replacement to improve mechanical properties and environmental sustainability and presents it as a viable alternative for sustainable construction. Additionally, a life cycle assessment (LCA) was conducted on the produced mortars to quantitatively compare their environmental impacts using a cradle-to-gate approach. In mixtures, it was used by replacing the diatomite in the ratios of 1%, 2%, 3%, 4%, and 5% by weight of the fly ash. Workability, unit weight, flexural and compressive strength, abrasion resistance, elevated temperature resistance and microstructure analysis were carried out. The results indicated that replacing 1%, 2%, and 3% diatomite increased the compressive and flexural strength of mortars due to their higher specific surface area. Two percent replacement of diatomite provided the best results. FESEM results of 3% diatomite inclusion showed more intense and compact microstructure of geopolymer. Diatomite inclusion increased the abrasion resistance of geopolymer. Since 2% diatomite replacement was found to be optimum, the LCA results showed that geopolymer mortar with 2% diatomite has 25% lower impacts in terms of global warming potential and 10% lower impacts in terms of terrestrial ecotoxicity than conventional Portland cement mortar.