Scopus İndeksli Yayınlar Koleksiyonu
Permanent URI for this collectionhttps://hdl.handle.net/20.500.12573/395
Browse
4 results
Search Results
Article Effects of Strain Rate and Post Processing on Mechanical Properties of Additively Manufactured AlSi10Mg Alloys(Walter de Gruyter GmbH, 2026-01-12) Karaveli, K.K.; Bal, B.The mechanical properties of AlSi10Mg alloy fabricated by laser powder bed fusion (LPBF) were investigated under different strain rates and post-processing conditions, including shot peening (SP) and stress relief (SR). Tensile tests were performed at quasistatic (0.1 s−1) and dynamic (0.015 s−1) strain rates on as-built and post-processed specimens. The results revealed that SP significantly increased the yield strength by 7.10 %, reaching 249.59 MPa, due to the induced compressive residual stresses. However, while SP slightly improved the ultimate tensile strength (UTS) by 0.25 %, it also reduced elongation at break by 18.06 %, indicating a trade-off between strength and ductility. Conversely, SR improved ductility by reducing internal stresses, leading to an elongation at break increase of 574.01 %, with a slight reduction in yield strength. The combination of SP and SR exhibited a synergistic effect, achieving a balance between strength and ductility. Strain rate sensitivity (SRS) analysis indicated that stress-relieved specimens performed better under dynamic loading conditions. These findings highlight the potential of post-processing techniques in tailoring the mechanical behavior of LPBF-produced AlSi10Mg alloys. The balanced properties achieved through combined treatments make this material particularly suitable for high-performance aerospace and automotive applications, where strength and ductility are critical under varying operational conditions. © 2025 Walter de Gruyter GmbH, Berlin/Boston.Article Citation - WoS: 125Citation - Scopus: 149Microstructure and Tribological Properties of TiTaHfNbZr High Entropy Alloy Coatings Deposited on Ti-6Al Substrates(Elsevier Sci Ltd, 2019-02) Tuten, N.; Canadinc, D.; Motallebzadeh, A.; Bal, B.We report on the microstructure and tribological behavior of equimolar TiTaHfNbZr high entropy alloy (HEA) thin films deposited on the biomedical Ti-6Al-4V substrates by RF magnetron sputtering. Results of nanoindentation and sliding wear experiments were evaluated along with the microstructure and topographical information obtained from scanning electron microscopy and atomic force microscopy. The findings clearly demonstrate that the TiTaHfNbZr HEA not only forms a homogenous and dense coating mechanically compatible with the Ti-6Al-4V substrates, but also provides a significantly enhanced surface protection against wear and cracking, which could prove valuable especially in long-term orthopedic implants that bear dynamic contact loading, such as in the cases of hip or knee joints.Article Citation - WoS: 39Citation - Scopus: 44Fracture Behavior of Novel Biomedical Ti-Based High Entropy Alloys Under Impact Loading(Elsevier Science SA, 2021-01) Gurel, S.; Yagci, M. B.; Canadinc, D.; Gerstein, G.; Bal, B.; Maier, H. J.This paper focuses on the mechanical properties and fracture behavior of newly developed body-centered-cubic structured TiTaHfNb, TiTaHfNbZr and TiTaHfMoZr high entropy alloys (HEAs) under impact loading as part of an effort to evaluate their potential utility as implant materials. The experimental findings showed all three Ti based HEAs have lower Young's modulus as compared to the conventionally used implant materials. Fractography analysis revealed that the TiTaHfNb HEA demonstrated significant ductility with the highest energy absorption capacity, while the TiTaHfNbZr and the TiTaHfMoZr alloys exhibited mixed mode fracture with relatively low ductility. Specifically, the reduction of ductility and energy absorption capacity under impact loading was attributed to the addition of Zr and Mo into Ti-based HEA system, which facilitates formation of additional dislocations in the microstructure due to increased lattice distortion. The current findings demonstrate that, from a mechanical point of view, the TiTaHfNb HEA could be considered as an alternative implant material for applications demanding high wear and corrosion resistance, such as hip or knee implants, and thus, warrant further investigation of the biomedical performance of this alloy.YArticle Citation - WoS: 102Citation - Scopus: 111Effect of Strain Rate on Hydrogen Embrittlement Susceptibility of Twinning-Induced Plasticity Steel Pre-Charged With High-Pressure Hydrogen Gas(Pergamon-Elsevier Science Ltd, 2016-09) Bal, B.; Koyama, M.; Gerstein, G.; Maier, H. J.; Tsuzaki, K.The effects of tensile strain rate on the hydrogen-induced mechanical and microstructural features of a twinning-induced plasticity (TWIP) steel were investigated using a Fe-23Mn-0.5C steel with a saturated amount of hydrogen. To obtain a homogeneous hydrogen distribution, high-pressure hydrogen gas pre-charging was performed at 423 K. Similar to previous studies on hydrogen embrittlement, the deterioration in the tensile properties became distinct when the strain rate was decreased from 0.6 x 10(-3) to 0.6 x 10(-4) s(-1). In terms of microstructural features, hydrogen-precharging decreased the thickness of deformation twin plates, and it localized dislocation slip. Moreover, facets of the hydrogen induced quasi-cleavage feature on the fracture surface became smoother with decreasing strain rate. In this study, we proposed that a combined effect of hydrogen segregation, slip localization, and thinning of twin plates causes the hydrogen embrittlement of TWIP steels, particularly at a low strain rate. (C) 2016 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.