Scopus İndeksli Yayınlar Koleksiyonu
Permanent URI for this collectionhttps://hdl.handle.net/20.500.12573/395
Browse
2 results
Search Results
Conference Object Citation - Scopus: 1On the Variation in Several Rock Properties due to Magnesium Sulfate Weathering Tests ‒ A Case Study for Limestones(International Multidisciplinary Scientific Geoconference, 2019-06-20) Köken, E.Contributions to the behavior of rock materials under various conditions provide a practical knowledge about issues relating the performance and long-term serviceability of rocks. In this study, various limestones with varying textural features were investigated in terms of their resistance against magnesium sulfate weathering tests. For this purpose, initial physico-mechanical properties of limestones were determined. Then, rock materials were subjected to magnesium sulfate weathering tests (up to 20 cycles) and the variation in physico-mechanical properties were determined for each rock type. As a result of laboratory tests, compared to initial rock properties, effective porosity (ne, %) increased in the range of 3% ‒ 14% and 12% ‒ 35% after 10th and 20th magnesium sulfate weathering cycles, respectively. Uniaxial compressive strength of rocks (UCS, MPa) decreased by 9% ‒ 24% after 10th cycles and by 32% – 58% after 20th cycles. Brazilian tensile strength of rocks (BTS, MPa) decreased in the range of 7% ‒ 19% and 20% ‒ 49% after 10th and 20th cycles, respectively. Similar to the variations in UCS and BTS, Tangential Young Modulus (Eti, GPa) also decreased at a rate of 13% ‒ 28% and 23% ‒ 64% after 10th and 20th cycles, respectively. However, the values of Tangential Poisson’s Ratio (vti) fluctuated with progressive accelerated weathering cycles, which could be linked to varying axial and lateral strain rates at 50% of UCS values for the limestones investigated. Furthermore, the variation in crack initiation stress σCI (MPa) due to progressive magnesium sulfate tests were also evaluated considering two strain-based methods and the findings showed that σCI of limestones slowly decreased with increasing weathering test cycles. It could be claimed that cyclic magnesium sulfate tests performed on rock materials would be beneficial for assessing the long-term serviceability of rocks. In this context, mud-supported limestones seem to have a greater resistance against magnesium sulfate weathering tests compared to the grain-supported ones. However, the number of samples should be increased in order to achieve a comprehensive understanding about the degradation processes of limestones. © 2021 Elsevier B.V., All rights reserved.Article Citation - WoS: 5Citation - Scopus: 6Effect of Pre-Rolling Temperature on the Interfacial Properties and Formability of Steel-Steel Bilayer Sheet in Single Point Incremental Forming(Sage Publications Ltd, 2020-10-14) Hassan, Malik; Hussain, Ghulam; Ali, Aaqib; Ilyas, Muhammad; Malik, Sohail; Khan, Wasim A.; Bal, BurakThe aim of this research was to investigate the effect of pre-rolling temperature on the interfacial properties in delamination modes 1 and 2; and formability in Single Point Incremental Forming (SPIF) of Steel-Steel (St-St) bilayer sheet prepared by roll bonding process. The roll bonding process was performed at three pre-rolling temperatures, 700 degrees C, 800 degrees C, and 950 degrees C, with a constant thickness reduction ratio of 58%. The bond strength and critical strain energy release rate (CSERR) were measured to characterize the interface of St-St bilayer sheet. T-peel test for mode 1 and tensile shear test for mode 2 were conducted to determine the interfacial properties. The formability of St-St bilayer sheet in SPIF was measured in terms of maximum wall angle. The results showed that the increase in pre-rolling temperature from 700 degrees C to 950 degrees C enhanced the bond strength and CSERR, in both mode 1 and 2. The enhancement in bond strength with an increase in pre-rolling temperature was 149.5% and 203% in mode 1 and 2, respectively. However, the increase in CSERR in mode 1 and 2 was 115% and 367%, respectively. The formability of St-St bilayer sheet also showed an increasing trend with an increase in pre-rolling temperature. Moreover, a consistent relation between formability and interfacial parameters was observed. It was also found that to successively deform the bilayer sheet into the desired shape, it is necessary for the sheet to be heated above the critical temperature during fabrication to facilitate good bonding between two sheets.