Scopus İndeksli Yayınlar Koleksiyonu
Permanent URI for this collectionhttps://hdl.handle.net/20.500.12573/395
Browse
2 results
Search Results
Article Citation - WoS: 1Citation - Scopus: 1Evaluating the Effects of Design and Manufacturing Parameters on Friction at the Surrogate Skin-3D Textile Interface(Sage Publications Ltd, 2025-10-30) Temel-Cicek, Mevra; Cicek, Umur I.; Lloyd, Alex B.; Johnson, Andrew A.Additive manufacturing (AM) is increasingly employed in the development of 3D-printed wearables, including medical wrist supports, textiles, and protective garments. While the general tribological behavior of 3D-printed components has been widely studied, limited research has focused on the friction behavior of 3D-printed wearables when in contact with human skin, which is a crucial factor for improving wearer comfort by minimizing local skin friction. This study, therefore, investigates the influence of material type, manufacturing technology, and print parameters of 3D-printed textiles on frictional behavior against skin. Specimens were fabricated using three AM technologies: material extrusion (MEX), vat photopolymerization (VATP), and powder bed fusion (PBF). Each technology employed various materials and print parameters, specifically layer thickness (ranging from 0.05 to 0.3 mm) and print orientations (horizontal and vertical). Friction was measured using a custom-built handheld device at the interface between 3D-printed specimens and two surrogate skin models: lorica (representing the dorsal forearm) and silicone (representing the chest). The results revealed that friction was significantly influenced by both layer thickness and print orientation. For MEX specimens, acrylonitrile butadiene styrene, acrylonitrile styrene acrylate, and polycarbonate showed the highest friction, while for VATP, durable resin resulted in the highest friction coefficient. In contrast, PBF specimens exhibited very similar frictional behavior. Regarding layer thickness, higher values consistently resulted in the highest friction coefficients, regardless of manufacturing method or material type. These findings provide valuable insights for designers and engineers seeking to optimize the comfort of 3D-printed wearables, guiding the selection of suitable AM processes and parameters for products intended for direct skin contact.Article Citation - WoS: 1Citation - Scopus: 1Investigation of Friction Coefficient Changes in Recycled Composite Materials Under Constant Load(MDPI, 2023-09-18) Gunes, Aydin; Duzcukoglu, Hayrettin; Salur, Emin; Aslan, Abdullah; Sahin, Omer SinanThe surface quality of machine elements may deteriorate over time while operating under different conditions. This deterioration adversely affects the wear behavior in the contact areas, and these materials become unusable over time. In machine elements especially, the heat transfer, wear amount and surface roughness parameters in the contact area are very important in order for the system to work efficiently. In order to understand this change, composite materials were produced by adding spheroidal graphite cast iron (GGG40) with high lubricating properties at different rates to bronze (CuSn10), which is widely used as a self-lubricating bearing material. In this study, four different mixing ratios (B60D40, B70D30, B80D20 and B90D10) and B100, which is completely produced from bronze chips, were used for comparison purposes. In addition, these produced composite materials were compared with pure CuSn10 and pure GGG40 via double-acting isostatic hot pressing, and then the results were examined. The composite materials were made at two different temperatures (400 degrees C and 450 degrees C) and three different pressures (480 MPa, 640 MPa and 820 MPa) using recycled waste chips. Composites produced by recycling waste chips both reduce costs and make a positive contribution to the natural environment. Thus, more advantageous self-lubricating bearing materials will be produced, and the efficiency will be increased in these materials. The time-dependent variation in the friction coefficient observed after the wear tests performed under constant load is explained, and the resulting surface structures are presented with SEM images and EDS analyses. After the wear tests, it was observed that the process parameters used in production effectively influenced the wear behavior. In particular, when the production pressure was low (480 MPa), the wear behavior was adversely affected because sufficient bonding between the chips could not be achieved. In addition, as the amount of GGG40 used as a reinforcement material increased, the spheroidal graphite contained in it positively affected the wear behavior. The lubricating effect provided by this spheroidal graphite reduced wear in the contact area and the friction coefficient.