Scopus İndeksli Yayınlar Koleksiyonu
Permanent URI for this collectionhttps://hdl.handle.net/20.500.12573/395
Browse
19 results
Search Results
Article Citation - WoS: 1Citation - Scopus: 1A Comparative Study of Existing and Current On-Site Documentation of Anatolian Seljuk Kümbets(Elsevier Ltd, 2025-12) Güzelci, O.Z.; Türel, A.During the Anatolian Seljuk period (1077–1307), monumental tombs known as kümbets emerged as a distinct architectural typology in present-day Türkiye. 2D drawings of these structures, produced since the early 20th century, contain inconsistencies that necessitate verification and accurate documentation. This study digitally documents Anatolian Seljuk kümbets in 3D to generate updated 2D sections reflecting their current condition and compares these with previously published drawings. The methodology includes collecting available 2D sections, digitally documenting kümbets through field studies, generating new 2D sections from 3D models, and systematically comparing these datasets. Two image-based metrics are employed in the comparison: the Exact Pixel Match Ratio (EPMR), which evaluates pixel-level alignment, and the Structural Similarity Index Measure (SSIM), a standard indicator for visual similarity. The results provide a comparative framework for assessing previous drawings and present a verified, up-to-date dataset of kümbet sections for future research. © 2025 Elsevier B.V., All rights reserved.Article Citation - Scopus: 3Chaos in PID Controlled Nonlinear Systems(Korean Institute of Electrical Engineers, 2015) Ablay, G.Controlling nonlinear systems with linear feedback control methods can lead to chaotic behaviors. Order increase in system dynamics due to integral control and control parameter variations in PID controlled nonlinear systems are studied for possible chaos regions in the closed-loop system dynamics. The Lur’e form of the feedback systems are analyzed with Routh’s stability criterion and describing function analysis for chaos prediction. Several novel chaotic systems are generated from second-order nonlinear systems including the simplest continuous-time chaotic system. Analytical and numerical results are provided to verify the existence of the chaotic dynamics. © 2021 Elsevier B.V., All rights reserved.Article Fuzzy Logic-Enhanced PMC Index for Assessing Policies for Decarbonization in Higher Education: Evidence from a Public University(MDPI, 2025-10-09) Fidan, Fatma Sener; Şener Fidan, FatmaHigher education institutions play a critical role in the transition to a low-carbon future due to their research capacity and societal influence. Accordingly, the calculation of greenhouse gas (GHG) emissions and the prioritization of mitigation strategies are of particular importance. In this study, a comprehensive campus-level GHG inventory was prepared for a public university in T & uuml;rkiye in alignment with the ISO 14064-1:2018 standard, and mitigation strategies were evaluated. To prioritize these strategies, both the classical Policy Modeling Consistency (PMC) index and, for the first time in the literature, a fuzzy extension of the PMC model was applied. The results reveal that the total GHG emissions for 2023 amounted to 4888.63 tCO2e (1.19 tCO2e per capita), with the largest shares originating from investments (31%) and purchased electricity (28.38%). While the classical PMC identified only two high-priority actions, the fuzzy PMC reduced score dispersion, resolved ranking ties, and expanded the number of high-priority actions to seven. The top strategies include awareness programs, energy-efficiency measures, virtual meeting practices, advanced electricity monitoring, and improved data management systems. By comparing the classical and fuzzy approaches, the study demonstrates that integrating fuzzy logic enhances the transparency, reproducibility, and robustness of strategy prioritization, thereby offering a practical roadmap for campus decarbonization and sustainability policy in higher education institutions.Article Citation - WoS: 1Citation - Scopus: 1Evaluating the Effects of Design and Manufacturing Parameters on Friction at the Surrogate Skin-3D Textile Interface(Sage Publications Ltd, 2025-10-30) Temel-Cicek, Mevra; Cicek, Umur I.; Lloyd, Alex B.; Johnson, Andrew A.Additive manufacturing (AM) is increasingly employed in the development of 3D-printed wearables, including medical wrist supports, textiles, and protective garments. While the general tribological behavior of 3D-printed components has been widely studied, limited research has focused on the friction behavior of 3D-printed wearables when in contact with human skin, which is a crucial factor for improving wearer comfort by minimizing local skin friction. This study, therefore, investigates the influence of material type, manufacturing technology, and print parameters of 3D-printed textiles on frictional behavior against skin. Specimens were fabricated using three AM technologies: material extrusion (MEX), vat photopolymerization (VATP), and powder bed fusion (PBF). Each technology employed various materials and print parameters, specifically layer thickness (ranging from 0.05 to 0.3 mm) and print orientations (horizontal and vertical). Friction was measured using a custom-built handheld device at the interface between 3D-printed specimens and two surrogate skin models: lorica (representing the dorsal forearm) and silicone (representing the chest). The results revealed that friction was significantly influenced by both layer thickness and print orientation. For MEX specimens, acrylonitrile butadiene styrene, acrylonitrile styrene acrylate, and polycarbonate showed the highest friction, while for VATP, durable resin resulted in the highest friction coefficient. In contrast, PBF specimens exhibited very similar frictional behavior. Regarding layer thickness, higher values consistently resulted in the highest friction coefficients, regardless of manufacturing method or material type. These findings provide valuable insights for designers and engineers seeking to optimize the comfort of 3D-printed wearables, guiding the selection of suitable AM processes and parameters for products intended for direct skin contact.Article Citation - WoS: 1Citation - Scopus: 2Green Synthesis and Characterization of Zinc Oxide Nanoparticles via Thyme for Biomedical Applications: Effect of Plant Extract Concentration and Drying Method(Springer, 2025-10-15) Karakaya, Humeyra; Kizilates, Burcu; Erdem, IlkerGreen synthesis of nano particles using plant extracts is sustainable, cost-effective, and eco-friendly. However, the synthesis parameters are still being investigated. In this study, zinc oxide nanoparticles (ZnO NPs) were prepared via thyme extract (green synthesis) and the effect of synthesis parameters were investigated. Samples with different concentrations of thyme plant extract (PE) (10, 16 & 24% (v/v) PE / Zn salt solution) were prepared and two different drying methods (freeze-drying (FD) and oven-drying (OD)) were performed. XRD results showed the hexagonal crystalline ZnO were formed with considerable crystallinity (70.8-75.1%) without further heat treatment (calcination). The crystallite sizes of ZnO NPs were determined to be in the range of 11.9-14.8 nm. The ZnO NPs prepared via PE concentration of 16% (v/v) and freeze-drying was with the finest crystallite size (11.9 nm) and considerable crystallinity (72.9%). ZnO NPs prepared via FD method were found to have smaller particle sizes, thus providing a higher surface-to-volume ratio. DLS (dynamic light scattering) analysis was used for determining the particle size distribution (PSD) and surface charge of ZnO NPs at acidic, neutral and basic pH values. The antibacterial characteristics of ZnO NPs were determined against Gram (+) and (-) bacteria. The ZnO NPs with the finest microstructure (16% PE (v/v), FD) had the highest antibacterial activity. The green synthesized ZnO NPs prepared in this study may be promising candidates for various applications including biomaterials and biomedical applications with their fine microstructure and considerable antibacterial activity.Article Sustainable Stabilization of Peat Soil with Hybrid Geopolymer Jet Grout Columns(Springer Int Publ A.G., 2025-10-15) Yalcin, Hakan; Erol, Aykut; Kaya, Zulkuf; Cadir, Cenk Cuma; Uncuoglu, Erdal; Akin, Muge K.Peat soils present severe challenges in geotechnical engineering due to their low shear strength, high water content, and aggressive chemical environments such as sulfate exposure. While cement-based jet grouting (JG) is widely used, it entails high carbon emissions and energy consumption. Hybrid geopolymer jet grout columns (HGJGCs) are presented in this work as a viable and sustainable alternative. Unlike conventional geopolymer studies that rely on pre-cured molds later exposed to aggressive environments, this research simulates realistic field conditions by injecting fresh geopolymer directly into sulfate-rich peat, where early-age durability and strength are critical. To address early strength limitations commonly seen in aggressive situations, a tiny amount of cement was added to the fly ash/GGBFS-based combination. Crucially, there is no need for high heat because the mechanism cures at room temperature. Physical model testing, laboratory-scale jet grouting, and performance comparisons with conventional JGCs were all carried out. Results show that HGJGCs increased the bearing capacity of peat by 5.5 times, improved compressive strength (5.3-5.7 MPa), and reduced settlement more effectively than JGCs. Additionally, CO2 emissions were reduced by 25.14% due to lower binder-related emissions and energy demand. This work shows that hybrid geopolymer systems are a viable, low-carbon substitute for peat stabilization because they can function well in real-world, chemically demanding situations.Article Citation - WoS: 1Citation - Scopus: 1A Comprehensive Review on the Extraction and Recovery of Lithium from Primary and Secondary Sources: Advances Toward Battery-Grade Materials(Wiley, 2025-10-20) Top, Soner; Kursunoglu, Sait; Altiner, MahmutLithium-ion battery (LIB) technologies have become indispensable to modern energy systems, driving global demand for high-purity lithium compounds. This review focuses on lithium recovery and purification strategies for battery-grade lithium carbonate (Li2CO3) and lithium hydroxide (LiOH), addressing both primary sources (brines and minerals) and secondary sources (waste materials). Industrially established processes, such as evaporation-based brine treatment and conventional metallurgical methods, are discussed alongside emerging techniques, including membrane separation, solvent extraction, and CO2-assisted precipitation. Particular attention is given to lithium precipitation mechanisms, the behaviour of co-existing ions during extraction, and the specific quality requirements for cathode material synthesis. By evaluating process scalability, environmental impact, and product purity, this review provides a comprehensive understanding of current practices and future directions. Additionally, it highlights the growing importance of lithium in the context of accelerating electric vehicle (EV) adoption, underscoring the bright and expanding future of the lithium industry.Article Contributions Toward Net-Zero Carbon in the Water Sector: Application to a Case Study(IWA Publishing, 2025-09-01) Ramos, Helena M.; Perez-Sanchez, Modesto; Correia, Tiago; Bekci, E.; Besharat, M.; Kuriqi, Alban; Coronado-Hernandez, Oscar E.This study presents an integrated smart water-energy nexus framework combining IoT-based water monitoring, hybrid renewables (hydropower/solar/wind), and AI-driven optimization. Real-time sensor data enables automated grid management, while AI analytics optimize operations and predict maintenance needs through a closed-loop system. The solution achieves bidirectional energy exchange, with the full hybrid system (G + H + PV + W) reducing costs by 41.5% (<euro>831K) and LCOE by 57.2% (<euro>0.0475/kWh). Financial analysis confirms viability with 26.4% IRR and 3.8-year payback, while achieving negative CO2 emissions (-160,476 kg/year). Progressive renewable integration enhances all key performance indicators (KPIs), cutting OPEX by 89.9% (<euro>7,156/year) through optimized operations. Dual water-energy performance metrics (leakage, pressure, % renewable share) ensure balanced and sustainable grid management. Key innovations include IoT-energy synergy, AI-driven predictive maintenance, and circular resource efficiency. The framework demonstrates how smart water grids can achieve both economic and environmental benefits through renewable energy integration and advanced digital solutions.Article Citation - WoS: 1Citation - Scopus: 1Effect of Yttrium/Lanthanum-Doped Ultrasonically Assisted Nano-Hydroxyapatite on Remineralization and Bracket Bond Strength in Artificial Enamel Lesions(BMC, 2025-09-29) Ozturk, Taner; Mammadov, Elshan; Bulduk Karakaya, Humeyra; Yagci, Filiz; Dayan, Serkan; Yagci, AhmetBackground This in vitro study aimed to evaluate the remineralization efficacy of ultrasonically assisted yttrium fluoride-doped (Ult-YF3-nHAP) and lanthanum fluoride-doped (Ult-LaF3-nHAP) nano-hydroxyapatite (nHAP) on artificially induced enamel lesions (aWSLs), and to compare their performance with acidulated phosphate fluoride (APF) gel, fluoride varnish, casein phosphopeptide-amorphous calcium phosphate (CPP-ACP), and resin infiltrant (ICON). Methods This in vitro study followed a four-phase design: enamel lesion creation, application of remineralization agents, a 14-day treatment protocol, and post-treatment analyses using QLF, Micro-CT, SEM-EDX, and SBS testing. This study included 168 extracted human premolars, divided into eight experimental groups (n = 21 per group): (1) Demineralized control (no remineralization treatment), (2) Acidulated phosphate fluoride (APF) gel, (3) Fluoride varnish, (4) Casein phosphopeptide-amorphous calcium phosphate (CPP-ACP), (5) Ultrasonically assisted nHAP (Control nHAP), (6) Ult-YF3-nHAP, (7) Ult-LaF3-nHAP, and (8) Resin infiltrant (ICON). The aWSLs were created under laboratory conditions. Brackets were bonded to the teeth with composite material, and aWSLs were created under laboratory conditions. After lesion formation and at the end of the experimental process, micro-computed tomography (Micro-CT) and laser-assisted quantitative light fluorescence (QLF) analysis were performed to assess lesion progression and remineralization. Additionally, scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDX) and shear bond strength (SBS) tests were conducted at the end of the study. Statistical analysis was performed using one-way ANOVA, Kruskal-Wallis, and Mann-Whitney U tests, with a significance level of p < 0.05. Results The bracket bond strength test data showed no significant differences between the groups (p = 0.156). Significant differences were found among groups for QLF fluorescence recovery (Delta F, p < 0.001), with the Ult-YF3-nHAP group showing the greatest increase (median: +0.5, IQR: -1.4 to + 0.7), while the control group showed the greatest decrease (median: -12.1, IQR: -12.4 to -10.2). Micro-CT analysis also revealed significant differences between groups (p = 0.008). The APF Gel group showed values comparable to those of all other experimental groups. The highest remineralization values were recorded in the Ult-YF3-nHAP group (6.87 +/- 3.03 mm(3)), whereas the lowest values were found in the Varnish group. The demineralized control group had significantly higher values than the Varnish group, but lower than the Ult-LaF3-nHAP group. SEM-EDX analysis revealed that fluoride weight was significantly lower in the Tooth Mousse and Varnish groups compared to the other experimental groups (p < 0.001). Ca/P ratio was significantly lower in the demineralized control, Varnish, and Ult-YF3-nHAP groups than in other experimental groups (p = 0.002). Conclusion Ult-YF3-nHAP showed higher efficacy in remineralization of aWSLs compared to fluoride-based treatments, CPP-ACP, and resin infiltrant. The highest remineralization was detected in the Ult-YF3-nHAP group by micro-CT and QLF analysis, while fluoride varnish gave the lowest result.Correction Correction: Engineering Novel Features for Diabetes Complication Prediction Using Synthetic Electronic Health Records(Frontiers Media S.A., 2025-08-29) Voskergian, Daniel; Bakir-Gungor, Burcu; Yousef, Malik