Scopus İndeksli Yayınlar Koleksiyonu
Permanent URI for this collectionhttps://hdl.handle.net/20.500.12573/395
Browse
15 results
Search Results
Article Citation - WoS: 1Citation - Scopus: 1Zinc Chalcogenide Based Shell Layers for Colloidal Quantum Wells(Wiley, 2025-04-27) Aldemir, Cagatay Han; Yazici, Ahmet Faruk; Ergezer, Nehir; Korkmaz, Taha Can; Mutlugun, Evren; Kelestemur, YusufColloidal quantum wells, also known as colloidal nanoplatelets (NPLs), have emerged as a promising class of materials for light-emitting devices (LEDs). However, the most widely studied core/shell NPLs, which rely on cadmium-based shell layers, face challenges due to toxicity concerns and improper charge confinement. To address these limitations, a new synthetic approach is presented that enables the controlled growth of zinc chalcogenide-based shell layers on NPLs. The synthesized CdSe/ZnSe core/shell NPLs exhibit emission between 615 and 630 nm, with a moderate photoluminescence quantum yield (PL-QY) of 40-50%. It is also demonstrated that the lateral dimensions of the CdSe core NPLs significantly affect the optical properties of the core/shell heterostructures, with smaller lateral dimensions resulting in narrower emission linewidths as low as 20 nm. Further passivation of these core/shell NPLs with an additional ZnS shell layer significantly increases the PL-QY up to 80-90%. Finally, the device performance of these two core/shell NPLs is investigated by fabricating solution-processed LEDs. With LEDs incorporating CdSe/ZnSe/ZnS core/multi-shell NPLs as the active light-emitting layer, an external quantum efficiency (EQE) of 3.82% and a maximum brightness of 6477 cd m-2 is obtained. These findings underscore the significant potential of zinc chalcogenide-based shell layers in advancing colloidal NPLs toward high-performance light-emitting devices.Article Citation - WoS: 2Citation - Scopus: 1Toward Sustainable Optoelectronics: Solution-Processed Quantum Dot Photodetector Fabrication Using a Surgical Blade(SPIE - Society of Photo-Optical Instrumentation Engineers, 2023-02-13) Savas, Muzeyyen; Yazici, Ahmet Faruk; Arslan, Aysenur; Mutluguen, Evren; Erdem, Talha; Yazlcl, Ahmet Faruk; Mutlugün, EvrenFabrication of optoelectronic devices relies on expensive, energy-consuming conventional tools including chemical vapor deposition, lithography, and metal evaporation. Furthermore, the films used in these devices are usually deposited at elevated temperatures (> 300 degrees C) and under high vacuum, which necessitate further restrictions on the device fabrication. Developing an alternative technology would contribute to the efforts on achieving a sustainable optoelectronics technology. Keeping this in our focus, here we present a simple technique to fabricate visible photodetectors (PDs). These fully solution-processed and transparent metal-semiconductor-metal (MSM) PDs employ silver nanowires (Ag NW) as the transparent electrodes replacing the indium-tin-oxide (ITO) commonly used in optoelectronic devices. By repeatedly spin coating Ag NWs on a glass substrate followed by the coating of zinc oxide nanoparticles, we obtained a highly conductive transparent electrode reaching a sheet resistance of 95 omega/? as measured by the four-probe method. Optical spectroscopy revealed that the transmittance of the Ag NW-ZnO films was 84% at 450 nm while the transmittance of the ITO films was 90% at the same wavelength. Following the formation of the conductive film, we scratched it using a heated surgical blade to open a gap. The scanning electron microscope images indicate that a gap of similar to 30 mu m is opened forming an insulating line. As the active layer, we drop-casted red-emitting CdSe/ZnS core-shell quantum dots (QDs) onto this gap to form a MSM PD. These visible QD-based PDs exhibited responsivities and detectivities up to 8.5 mA/W and 0.95 x 109 Jones, respectively at a bias voltage of 5 V and wavelength of 650 nm. These proof-of-concept PDs show that the environmentally friendly, low-cost, and energy-saving technique presented here can be an alternative to conventional, high-cost, and energy-hungry techniques while fabricating photoconductive devices.Article Citation - WoS: 25Citation - Scopus: 22Tattoo-Like Multi-Color Physically Unclonable Functions(Wiley-VCH Verlag GmbH, 2023-12-07) Kiremitler, N. Burak; Esidir, Abidin; Drake, Gryphon A.; Yazici, Ahmet Faruk; Sahin, Furkan; Torun, Ilker; Onses, M. SerdarAdvanced anti-counterfeiting and authentication approaches are in urgent need of the rapidly digitizing society. Physically unclonable functions (PUFs) attract significant attention as a new-generation security primitive. The challenge is design and generation of multi-color PUFs that can be universally applicable to objects of varied composition, geometry, and rigidity. Herein, tattoo-like multi-color fluorescent PUFs are proposed and demonstrated. Multi-channel optical responses are created by electrospraying of polymers that contain semiconductor nanocrystals with precisely defined photoluminescence. The universality of this approach enables the use of dot and dot-in-rod geometries with unique optical characteristics. The fabricated multi-color PUFs are then transferred to a target object by using a temporary tattoo approach. Digitized keys generated from the red, green and blue fluorescence channels facilitate large encoding capacity and rapid authentication. Feature matching algorithms complement the authentication by direct image comparison, effectively alleviating constraints associated with imaging conditions. The strategy that paves the way for the development of practical, cost-effective, and secure anticounterfeiting systems is presented. Tattoo-like multi-color encoding layers based on random processing of semiconductor nanocrystals of varied composition and geometry are reported. Additive deposition via chaotic electrospraying enables randomness and multiplexing, whereas the tattoo approach provides substrate independence.imageArticle Citation - WoS: 16Citation - Scopus: 17Solid-State Encapsulation and Color Tuning in Films of Cesium Lead Halide Perovskite Nanocrystals for White Light Generation(Amer Chemical Soc, 2019-01-30) Torun, Ilker; Altintas, Yemliha; Yazici, Ahmet Faruk; Mutlugun, Evren; Onses, M. SerdarPerovskite nanocrystals (PNCs) are highly demanding nanomaterials for solid-state lighting applications. A challenge for their exploitation in practical applications is the insufficient ambient and water stability associated with their ionic nature. Here we report a novel route for solid-state encapsulation of films of perovskite nanocrystals (PNCs) through vapor-phase deposition of a thin and hydrophobic layer of fluoroalkyltrichlorosilanes (FAS). High quality nanoscale crystals of CsPbBr3 were synthesized with well established colloidal methods and coated on solid substrates. The films of PNCs were then subjected to vapor of FAS for short durations of time (<60 s) in ambient atmosphere, resulting in deposition of a thin (<20 nm) hydrophobic layer. Besides providing a barrier for water and humidity, the vapor-phase deposition of FAS was accompanied by the blue shift of the emission wavelength of the PNCs. The color shift results from the partial exchange of Br with Cl anions, which emerge during the self-hydrolysis of the silane molecules. Throughout this process, we demonstrate the enhanced water stability of the films of PNCs and fine tunability of the wavelength in films from 516 nm to 488 nm. The fabrication of a white-light-emitting diode and tunability of the color coordinates with the duration of the FAS deposition were demonstrated. The rapid, scalable, and inexpensive solid-state encapsulation approach shows great promise for films of halide perovskites.Conference Object Simple, Sustainable Fabrication of Fully Solution-Processed, Transparent, Metal-Semiconductor Photodetectors Using a Surgical Blade as an Alternative to Conventional Tools(SPIE - The International Society for Optics and Photonics, 2022-05-24) Savas, Muzeyyen; Yazici, Ahmet Faruk; Arslan, Aysenur; Mutlugun, Evren; Erdem, Talha; Yazic, Ahmet Faruk; Erdem1, TalhaFabrication of optoelectronic devices relies on the expensive, energy-consuming conventional tools such as chemical vapor deposition, lithography, and metal evaporation. Furthermore, the films used in these devices are usually deposited at elevated temperatures and under vacuum that impose further restrictions to the device fabrication. Developing an alternative technology would contribute to the efforts on achieving a more sustainable optoelectronics technology. Keeping this focus in our focus, here we present a simple technique to fabricate visible photodetectors. These fully solution-processed and transparent metal-semiconductor-metal photodetectors employ silver nanowires (Ag NW) as the transparent electrodes replacing the indium-tin oxide (ITO) commonly used in optoelectronic devices. By repeatedly spin coating Ag NWs on a glass substrate followed by the coating of ZnO nanoparticles, we obtained a highly conductive transparent electrode reaching a sheet resistance of 95 Omega/square as measured by the four-probe method. Optical spectroscopy revealed that the transmittance of the Ag NW-ZnO films was 84% at 450 nm while transmittance of the ITO films was 90% at same wavelength. Following the formation of the conductive film, we scratched it using a heated surgical blade to open a gap. The scanning electron microscope images indicate that a gap of similar to 30 mm is opened forming an insulating line. As the active layer, we drop-casted red-emitting CdSe/ZnS core-shell quantum dots (QDs) on to this gap to form a metal-semiconductor-metal photodetector. These visible QD- based photodetectors exhibited responsivities and detectivities up to 8.5 mA/W and 0.95x10(9) Jones, respectively. These proof-of-concept photodetectors show that the environmentally friendly, low- cost, and energy-saving technique presented here can be an alternative to conventional, more expensive, and energy-hungry techniques while fabricating light-harvesting devices.Article Citation - WoS: 13Citation - Scopus: 15Rational Design of Chemical Bath Deposition Technique for Successful Preparation of Mn-Doped CdS Nanostructured Thin Films With Controlled Optical Properties(Elsevier Sci Ltd, 2021-02) Kharabaneh, Farzaneh Khani; Ghavidel, Elham; Soheyli, Ehsan; Yazici, Ahmet Faruk; Jawhar, Nawzad Nadhim; Mutlugun, Evren; Sahraei, RezaThe introduction of a rational design for depositing internally-doped nanostructured thin films is of great importance for optoelectronics. In this presented work, Mn-doped CdS thin films with high purity in composition were prepared through the chemical bath deposition technique using a nucleation-doping strategy. This work focuses on an improved chemical design to eliminate mostly ignored property of conventionally doped nanoscale thin films. The synthesis strategy was initiated by the initial formation of MnS nuclei in a colloidal depositing solution followed by injection of cadmium precursor to diffuse into the initial nuclei and play the role of host CdS matrix which was the beginning of the deposition process. Upon optimization of the PL-emission, it was revealed that relative intensity of Mn2+-related peak to the excitonic peak has significantly increased (similar to 100 times) in 80 degrees C, pH = 6, and precursor molar ratio of Cd:Mn:EDTA:S equal to 1:3:0.4:5, at deposition time of 300-min. The TRPL measurements further revealed the effective contribution of Mn-related midgap states with long-lived decay curve character, which confirms the success of the designed approach to reach internally doped thin films. It was found that the deposition temperature, amount of Cd/Mn/TA precursors, and deposition time are the most important experimental parameters in the proposed synthesis approach. Due to the versatility, generality, and colloidal advantages of this method, it can be extended to the other structures with various types of dopant agent.Article Citation - WoS: 24Citation - Scopus: 26Preparation of Highly Emissive and Reproducible Cu-In-S/ZnS Core/Shell Quantum Dots With a Mid-Gap Emission Character(Elsevier Science SA, 2020-05) Jawhar, Nawzad Nadhim; Soheyli, Ehsan; Yazici, Ahmet Faruk; Mutlugun, Evren; Sahraei, RezaCopper indium sulfide (CIS) quantum dots (QDs) are one of the newest types of luminescent semiconductors with low-toxicity and earth-abundant features. The present work reports the successful aqueous synthesis of CIS/ZnS core/shell QDs using dual-stabilizing agents of N-acetyl-L-cysteine and trisodium citrate. Off-stoichiometric QDs with In-rich compositions were found to be very small and highly emissive after coating by a shell of wide bandgap ZnS. The effect of various experimental parameters was evaluated to achieve highly reproducible QDs with bright reddish emission. Results showed a significant contribution of mid-gap defect states in the recombination processes (based on the gradual increase in absorbance recorded for samples, relatively high Urbach energy, large Stokes shift, large FWHM value in PL spectra, as well as the long-lived PL decay time). In addition, the chemical stability of samples was investigated using highly oxidant H2O2 agent and results demonstrate their superior stability. The combination of low-toxicity, intense and stable emission, along with synthetic advantages demonstrates that the present aqueous-soluble and emissive QDs can be considered as an excellent bio-photonic structure suitable for different fields of biological imaging and diagnostics. (C) 2020 Elsevier B.V. All rights reserved.Article Citation - WoS: 9Citation - Scopus: 11Natural Wax-Stabilized Perovskite Nanocrystals as Pen-On Inks and Doughs(Amer Chemical Soc, 2022-04-19) Ocal, Sema Karabel; Kiremitler, N. Burak; Yazici, Ahmet Faruk; Celik, Nusret; Mutlugun, Evren; Onses, M. Serdar; Karabel Ocal, SemaPerovskite nanocrystals (PNCs) are emerging luminescent materials for a wide range of technological applications. The broad adaptation of PNCs will be greatly improved by addressing their intrinsically low stability and developing processes for their assembly into 2D and 3D structures using facile approaches. Inspired by the mechanism of natural protection of leaves, this paper proposes natural carnauba wax (CW) as an encapsulation material for PNCs. The synthesis of PNCs is performed in the presence of CW, which is derived from the leaves of Copernicia prunifera palm. CW acts as a solvent and replaces the commonly used octadecene in the preparation of PNCs. The facile synthesis in CW results in PNCs with greatly improved thermal, water, and air stability. Furthermore, the thermal and mechanical properties make PNC-Wax a highly suitable solid ink for versatile processing of these materials into 2D and 3D architectures. PNC-Wax can be printed via a pen-on-paper approach by heating at modest temperatures. The rapid plasticization of PNC-Wax by mechanical agitation enables hand-shaping of the material in a manner similar to playdoughs, which would possibly enable the versatile use of this material for various applications.Article Citation - WoS: 12Citation - Scopus: 14Nanowire-Shaped MoS2@MoO3 Nanocomposites as a Hole Injection Layer for Quantum Dot Light-Emitting Diodes(Amer Chemical Soc, 2022-08-01) Bastami, Nasim; Soheyli, Ehsan; Arslan, Aysenur; Sahraei, Reza; Yazici, Ahmet Faruk; Mutlugun, EvrenMolybdenum disulfides and molybdenum trioxides are structures that possess the potential to work as efficient charge transport layers in optoelectronic devices. In the present study, as opposed to the existing Mo-based nanostructures in flake, sheet, or spherical forms, an extremely simple and low-cost hydrothermal method is used to prepare nanowires (NWs) of MoS2@MoO3 (MSO) composites. The synthesis method includes several advantages including easy handling and processing of inexpensive precursors to reach stable MSO NWs without the need for an oxygen-free medium, which would facilitate the possibility of mass production of these nanostructures. The structural analysis confirmed the formation of MSO nanocomposites with different Mo valence states, as well as NWs of average length and diameter of 70 nm and 5 nm, respectively. In order to demonstrate their potential for optoelectronic applications, MSO NWs were blended into hole injection layers (HILs) in quantum dot-based light emitting diodes (QLEDs). Electroluminescence measurements show a substantial enhancement in both luminance (from 44,330 to 68,630 cd.m-2) and external quantum efficiency (from 1.6 to 2.3%), based on the increase in the ratio of MSO NWs from 3 to 10%. Interestingly, the addition of 10% volume of MSO NWs resulted in a remarkably smoother HIL with improved current efficiency and stability in green-emitting QLEDs. The simplicity and cost-effective features of the synthesis method along with outstanding favorable morphology demonstrated their ability to enhance the QLED performance and mark them as promising agents for optoelectronics.Article Citation - WoS: 52Citation - Scopus: 52Multiplexed Patterning of Cesium Lead Halide Perovskite Nanocrystals by Additive Jet Printing for Efficient White Light Generation(Elsevier Science SA, 2020-01) Altintas, Yemliha; Torun, Ilker; Yazici, Ahmet Faruk; Beskazak, Emre; Erdem, Talha; Onses, M. Serdar; Mutlugun, Evren; Serdar Onses, M.Inorganic perovskite nanocrystals (PNCs) offer the ability to precisely but also flexibly control the peak emission wavelength while also possessing narrow-band emission spectra and high quantum yields. Owing to these features, PNCs have been already employed as color converters on LEDs. Nevertheless, the anion exchange reactions that prevent the blending of perovskites of different colors remain as an important bottleneck. As a remedy to this issue, here we employ additive jet printing to form separated stripes of these nanocrystals. Within this framework, we first present the synthesis of CsPbBr3 and CsPbBrxI3-x nanocrystals spanning the whole visible regime and optimize the cleaning procedure to obtain PNCs possessing photoluminescence quantum yields as high as 91% and emission linewidths as narrow as 15 nm, making them suitable for high quality white light generation. Next, we employ electrohydrodynamic jet printing to form closely spaced stripes of PNCs of various colors and integrated these films with a blue LED to create a white LED. Our proof-of-concept LED achieves high photometric performance as it possesses a color rendering index of 91.3, luminous efficacy of optical radiation > 300 lm/W-opt, and correlated color temperature of ca. 7000 K. We believe that additive jet printing technique will pave the way for a ubiquitous use of these PNCs in light-emitting devices in the near future.