Scopus İndeksli Yayınlar Koleksiyonu
Permanent URI for this collectionhttps://hdl.handle.net/20.500.12573/395
Browse
2 results
Search Results
Article Citation - WoS: 2Citation - Scopus: 4A Study of the Relationship Between the Pressuremeter Modulus and the Preconsolidation Pressure Around a Thrust Fault(Springer, 2019-10) Ozvan, Ali; Ozvan, Elif E.; Akkaya, Ismail; Akin, Mutluhan; Akin, Muge K.The study area is in a zone under the influence of the Lake Van water changes and the Van fault, which caused a destructive earthquake in 2011. Due to the level changes of Lake Van, sediments with different thicknesses as well as grain sizes were deposited in this region and the characteristics of these sediments were significantly affected by the morphology and lake water fluctuations in the past. A total of six boreholes were drilled along a 3-km line within the study area to determine the preconsolidation pressure (sigma(pc)) and the pressuremeter test values of the clayey levels of old lake deposits-which are known to have different physical and mechanical properties-with hopes to gain an insight on how they influence the mechanical tests performed in the field and in laboratory conditions. The relationship between these values was also statistically evaluated. When both datasets were evaluated together, it was determined that the stresses in the area close to the Van Thrust Fault plane caused deformations in the soil, which in turn affected the hanging-wall block of the thrust fault in particular. The inspection of E-M and sigma(pc) values for the area within the primary compression zone of the Van Fault revealed that both values of the boreholes on the footwall block were higher compared to other boreholes close to the lake (southwest). This finding indicates that the fault stresses at the footwall block of the fault plane enhance the mechanical characteristics of the soil. The data obtained were also evaluated using regression analysis. Relationships between all available data were investigated and a high coefficient of determination was derived between the Menard deformation modulus (E-M) and the preconsolidation (sigma(pc)) pressure.Article Citation - WoS: 8Citation - Scopus: 9A New Quantitative Welding Degree Classification for Ignimbrites(Springer, 2023-06-28) Akin, Mutluhan; Topal, Tamer; Dincer, Ismail; Akin, Muge K.; Ozvan, Ali; Orhan, Ahmet; Orhan, AyseAs a pyroclastic rock type, ignimbrites may reveal varying degrees of welding depending on the temperature (> 535 celcius) and overburden pressure conditions during its formation. The welding degree of ignimbrites increases as the formation temperature and the thickness of the overburden deposit in the depositional environment escalate, which are the most crucial factors controlling the rate of welding in ignimbrites. With the increasing temperature, plastic deformation is observed in ignimbrites and the glassy minerals are being welded. Furthermore, the thickness of the overburden causes the deformation of the ash matrix in ignimbrites at the lower sections and the pumice grains are flattened at different rates. An increase in the degree of welding of ignimbrites causes an improvement in the physical and mechanical properties of the rock material as well. Within the scope of this research, petrographical, mineralogical, and geochemical studies were carried out on a total of 16 different ignimbrite types, which have different color and texture properties, obtained from three different regions of Turkey (Kayseri, Nevsehir, Ahlat) where ignimbrites extensively crop out, and the physical and mechanical properties of these samples were revealed. Consequently, a new welding classification was developed for ignimbrites considering the uniaxial compressive strength and dry unit weight. The proposed welding classification consists of six classes ranging from non-welded to highly welded. When the welding degrees of the selected ignimbrites are evaluated, Kayseri ignimbrites mostly exhibit moderate welding characteristics. Nevsehir ignimbrites, on the other hand, have a low welding degree whereas the degree of welding in Ahlat ignimbrites may vary from low to high. Additionally, long and short axis lengths of pumice grains in the ignimbrite specimens were determined by measuring under the microscope, and shape ratios were determined by different shape parameter evaluation methods. As a result, it has been concluded that the pumice grains in Kayseri and Ahlat ignimbrites have a more lenticular structure than the pumice grains in Nevsehir ignimbrites. Eventually, the welding degree classes of ignimbrites and the classification developed by using threshold values of the oblateness ratio (OR) values of pumice grains at different welding degrees are quite compatible. The proposed welding degree classification is of great importance in the selection of ignimbrites widely used as dimension stone and in terms of engineering classification of this rock type as well as it will guide to the scientific studies to be performed on ignimbrites with varying physical and mechanical properties.