Scopus İndeksli Yayınlar Koleksiyonu
Permanent URI for this collectionhttps://hdl.handle.net/20.500.12573/395
Browse
6 results
Search Results
Article Citation - WoS: 1Citation - Scopus: 1Seismic Site Classification via Vs30 and SPT-N Values in Antakya City, Türkiye(Taylor & Francis Ltd, 2026-01-22) Alosman, Salama Omar; Akin, Muge K.; Cabalar, Ali FiratThe paper presents an assessment for the seismic site classification (SSC) in Antakya city located in southern central T & uuml;rkiye, strongly affected by three destructive earthquakes of 7.7 Mw took place in Pazarcik (Kahramanmaras) on February 6, 2023, 7.6 Mw took place in Elbistan (Kahramanmaras) on February 6, 2023, and 6.4 Mw took place in Defne (Hatay) on February 20, 2023. The V-S30 and SPT-N values have been used to identify the SSC in the region with respect to the provisions recommended by the National Earthquake Hazards Reduction Program (NEHRP), Design of Structures for Earthquake Resistance (Eurocode 8), and Turkish Building Earthquake Code (TBEC). The values of SPT-N were recorded from the field works that include 630 boreholes in the top 30 m, whilst the V-S30 was calculated through the multichannel analysis of surface waves (MASW) method performed at 977 different locations across the region. The results showed that approximately 51% and 44% of soils in the city of Antakya has been classified as Class C and Class D, respectively, in accordance with the NEHRP and TBEC, whilst 52% and 44% of the same region has been classified as Class B and Class C, respectively, in accordance with the Eurocode 8. Furthermore, a newly proposed correlation as well as already available ones between the V-S30 and SPT-N values have been presented comparatively by an extensive series of GIS maps produced in order to have a much clear understanding on the various soil types in Antakya. Evidently, the results of this research should be of a great significance for researchers and practitioners working on the earthquake-resistant structures, prediction of ground movements, and in seismic risk assessments.Article Citation - WoS: 14Citation - Scopus: 14Experimental Studies on the Physico-Mechanical Properties of Jet-Grout Columns in Sandy and Silty Soils(Pergamon-Elsevier Science Ltd, 2016-04) Akin, Muge K.The term of ground improvement states to the modification of the engineering properties of soils. Jet grouting is one of the grouting methods among various ground improvement techniques. During jet grouting, different textures of columns can be obtained depending on the characteristics of surrounding subsoil as well as the adopted jet-grouting system for each site is variable. In addition to textural properties, strength and index parameters of jet-grout columns are highly affected by the adjacent soil. In this study, the physical and mechanical properties of jet-grout columns constructed at two different sites in silty and sandy soil conditions were determined by laboratory tests. A number of statistical relationships between physical and mechanical properties of soilcrete were established in this study in order to investigate the dependency of numerous variables. The relationship between q(u) and gamma(d) is more reliable for sandy soilcrete than that of silty columns considering the determination coefficients. Positive linear relationships between Vp and gamma(d) with significantly high determination coefficients were obtained for the jet-grout columns in silt and sand. The regression analyses indicate that the P-wave velocity is a very dominant parameter for the estimation of physical and mechanical properties of jet-grout columns and should be involved during the quality control of soilcrete material despite the intensive use of uniaxial compressive strength test. Besides, it is concluded that the dry unit weight of jet-grout column is a good indicator of the efficiency of employed operational parameters during jet-grouting. (C) 2016 Elsevier Ltd. All rights reserved.Article Citation - WoS: 15Citation - Scopus: 19Evaluation of Seismic Site Classification for Kahramanmaras City, Turkey(Springer, 2021-01-28) Naji, Dalia Munaff; Akin, Muge K.; Cabalar, Ali FiratThis paper presents a study on the seismic site classification map using the geophysical tests in Kahramanmaras city located at a place where African, Anatolian, and Arabian plates meeting in southern-central Turkey. Generating seismic site classification maps in accordance with National Earthquake Hazards Reduction Program (NEHRP) has become a more significant criterion for earthquake hazard estimations. The SPT-N values obtained from the field studies at 287 boreholes within the upper 30 m were used to describe the subsurface conditions in the region. The shear wave velocity (V-S) values in the study area were obtained by implementing Multichannel Analysis of Surface Waves (MASW) and Microtremor Array Method (MAM) measurements tests. An approach proposed by Boore (Boore, Bull Seismol Soc Am 94:591-597, 2004) for the cases where the V-S measurements do not reach 30 m depth has also been adopted by correlating the shallow shear wave velocity with V-S30. The resulting site classification maps estimate that the study area is predominantly classified as soil site class C, while the small areas were rarely classified as soil site class D and B. Furthermore, a systematic analysis based on a comparative study of the present research and the published correlations for seismic site classification with V-S30 values has been carried out using Geographical Information System (GIS). Evidently, the V-S30 based seismic site classification maps could be effectively used by researchers and engineers for the purpose of land-use planning and urban development in earthquake-prone regions.Article Citation - WoS: 15Citation - Scopus: 15Comparison of SPT and VS-Based Liquefaction Analyses: A Case Study in Ercis (Van, Turkey)(Springer International Publishing AG, 2017-12-08) Akkaya, Ismail; Ozvan, Ali; Akin, Mutluhan; Akin, Muge K.; Ovun, UgurLiquefaction which is one of the most destructive ground deformations occurs during an earthquake in saturated or partially saturated silty and sandy soils, which may cause serious damages such as settlement and tilting of structures due to shear strength loss of soils. Standard (SPT) and cone (CPT) penetration tests as well as the shear wave velocity (V-s)-based methods are commonly used for the determination of liquefaction potential. In this research, it was aimed to compare the SPT and V-s-based liquefaction analysis methods by generating different earthquake scenarios. Accordingly, the Ercis residential area, which was mostly affected by the 2011 Van earthquake (M-w = 7.1), was chosen as the model site. Ercis (Van, Turkey) and its surroundings settle on an alluvial plain which consists of silty and sandy layers with shallow groundwater level. Moreover, Caldiran, Ercis-Kocapinar and Van Fault Zones are the major seismic sources of the region which have a significant potential of producing large magnitude earthquakes. After liquefaction assessments, the liquefaction potential in the western part of the region and in the coastal regions nearby the Lake Van is found to be higher than the other locations. Thus, it can be stated that the soil tightness and groundwater level dominantly control the liquefaction potential. In addition, the lateral spreading and sand boiling spots observed after the 23rd October 2011 Van earthquake overlap the scenario boundaries predicted in this study. Eventually, the use of V-s-based liquefaction analysis in collaboration with the SPT results is quite advantageous to assess the rate of liquefaction in a specific area.Article Citation - WoS: 2Citation - Scopus: 4A Study of the Relationship Between the Pressuremeter Modulus and the Preconsolidation Pressure Around a Thrust Fault(Springer, 2019-10) Ozvan, Ali; Ozvan, Elif E.; Akkaya, Ismail; Akin, Mutluhan; Akin, Muge K.The study area is in a zone under the influence of the Lake Van water changes and the Van fault, which caused a destructive earthquake in 2011. Due to the level changes of Lake Van, sediments with different thicknesses as well as grain sizes were deposited in this region and the characteristics of these sediments were significantly affected by the morphology and lake water fluctuations in the past. A total of six boreholes were drilled along a 3-km line within the study area to determine the preconsolidation pressure (sigma(pc)) and the pressuremeter test values of the clayey levels of old lake deposits-which are known to have different physical and mechanical properties-with hopes to gain an insight on how they influence the mechanical tests performed in the field and in laboratory conditions. The relationship between these values was also statistically evaluated. When both datasets were evaluated together, it was determined that the stresses in the area close to the Van Thrust Fault plane caused deformations in the soil, which in turn affected the hanging-wall block of the thrust fault in particular. The inspection of E-M and sigma(pc) values for the area within the primary compression zone of the Van Fault revealed that both values of the boreholes on the footwall block were higher compared to other boreholes close to the lake (southwest). This finding indicates that the fault stresses at the footwall block of the fault plane enhance the mechanical characteristics of the soil. The data obtained were also evaluated using regression analysis. Relationships between all available data were investigated and a high coefficient of determination was derived between the Menard deformation modulus (E-M) and the preconsolidation (sigma(pc)) pressure.Article Citation - WoS: 9Citation - Scopus: 9A New Quantitative Welding Degree Classification for Ignimbrites(Springer, 2023-06-28) Akin, Mutluhan; Topal, Tamer; Dincer, Ismail; Akin, Muge K.; Ozvan, Ali; Orhan, Ahmet; Orhan, AyseAs a pyroclastic rock type, ignimbrites may reveal varying degrees of welding depending on the temperature (> 535 celcius) and overburden pressure conditions during its formation. The welding degree of ignimbrites increases as the formation temperature and the thickness of the overburden deposit in the depositional environment escalate, which are the most crucial factors controlling the rate of welding in ignimbrites. With the increasing temperature, plastic deformation is observed in ignimbrites and the glassy minerals are being welded. Furthermore, the thickness of the overburden causes the deformation of the ash matrix in ignimbrites at the lower sections and the pumice grains are flattened at different rates. An increase in the degree of welding of ignimbrites causes an improvement in the physical and mechanical properties of the rock material as well. Within the scope of this research, petrographical, mineralogical, and geochemical studies were carried out on a total of 16 different ignimbrite types, which have different color and texture properties, obtained from three different regions of Turkey (Kayseri, Nevsehir, Ahlat) where ignimbrites extensively crop out, and the physical and mechanical properties of these samples were revealed. Consequently, a new welding classification was developed for ignimbrites considering the uniaxial compressive strength and dry unit weight. The proposed welding classification consists of six classes ranging from non-welded to highly welded. When the welding degrees of the selected ignimbrites are evaluated, Kayseri ignimbrites mostly exhibit moderate welding characteristics. Nevsehir ignimbrites, on the other hand, have a low welding degree whereas the degree of welding in Ahlat ignimbrites may vary from low to high. Additionally, long and short axis lengths of pumice grains in the ignimbrite specimens were determined by measuring under the microscope, and shape ratios were determined by different shape parameter evaluation methods. As a result, it has been concluded that the pumice grains in Kayseri and Ahlat ignimbrites have a more lenticular structure than the pumice grains in Nevsehir ignimbrites. Eventually, the welding degree classes of ignimbrites and the classification developed by using threshold values of the oblateness ratio (OR) values of pumice grains at different welding degrees are quite compatible. The proposed welding degree classification is of great importance in the selection of ignimbrites widely used as dimension stone and in terms of engineering classification of this rock type as well as it will guide to the scientific studies to be performed on ignimbrites with varying physical and mechanical properties.