WoS İndeksli Yayınlar Koleksiyonu
Permanent URI for this collectionhttps://hdl.handle.net/20.500.12573/394
Browse
9 results
Search Results
Article Citation - WoS: 6Citation - Scopus: 6The Different Impacts of g-C3N4 Nanosheets on PVDF and PSF Ultrafiltration Membranes for Remazol Black 5 Dye Rejection(Wiley, 2023-08-02) Senol-Arslan, Dilek; Gul, Ayse; Dizge, Nadir; Ocakoglu, Kasim; Uzal, NigmetMembranes combined with nanoparticles are an excellent combination capable of successfully removing various contaminants, such as dyes from wastewater while using very little energy and decreasing pollution. The present study reports an efficient approach for Remazol Black 5 (RB5) dye removal using composite graphitic carbon nitride nanosheets (g-C3N4), polysulfone (PSF), and polyvinylidene fluoride (PVDF) membranes. The membranes were prepared using the phase inversion method, with varying quantities of g-C3N4 nanosheets ranging from 0.1%, 0.2% to 0.3%. The prepared g-C3N4 nanosheets were characterized by FTIR, SEM analyses, and zeta potential measurements. FTIR and SEM studies, contact angle, water permeability, COD, and dye rejection measurements were used to characterize the g-C3N4 nanosheets embedded in PSF and PVDF membranes. After the addition of 0.3 wt% g-C3N4, the water flux of the 0.3 wt% g-C3N4 embedded PSF membrane was the highest, whereas the water flux of the 0.3 wt% g-C3N4 embedded PVDF membrane was the lowest. The ultrafiltration (UF) membrane's performance with g-C3N4 embedded showed an RB5 rejection rate of more than 80% and a COD removal efficiency of more than 45%. The results of the experimental filtration showed that RB5 rejection reached maximum values of 91.3% for 0.1 wt% g-C3N4/PSF, and 85.6% for 0.3 wt% g-C3N4/PVDF.Article Citation - WoS: 4Citation - Scopus: 5Predicting Potential of Pressure Retarded Osmosis Power for Different Estuaries in Turkey(Wiley, 2018-11-29) Saki, Seda; Uzal, Nigmet; Gokcek, Murat; Ates, NurayPressure retarded osmosis (PRO) is an alternative renewable energy source recovered from the salinity gradient between the fresh water (feed solution) and salty water (draw solution). In order to implement osmotic power, the site-specific characteristics including the river and sea salinity, annual flow rates, ecological restrictions were taken into account. This study revealed a comprehensive analysis for a theoretical potential of PRO process for different estuaries in Turkey. In this study, the power potential prediction of PRO process for the Ceyhan, Sakarya, and Meric Rivers were analyzed via Gibbs free energy calculations. The net annual energy production is projected to be 167, 164, and 208 GWh/y for Ceyhan, Sakarya, and Meric Rivers, respectively. Meric River has the highest energy production of 208 GWh/yr with 186 m(3)/s mean flow rate and 245 mg/L salinity. These results clearly show that Turkey's rivers having high salinity and flow rate are feasible and applicable for making the osmotic power plant economically. Thereby, it is providing essential direction to the improvement of its design, installation, and operation. The developed methodology for the evaluation of the osmotic power potential of other rivers can be considered as a basis to assess the whole potential on a worldwide level. (c) 2018 American Institute of Chemical Engineers Environ Prog, 38:e13085, 2019Article Citation - WoS: 3Citation - Scopus: 3Investigation of the Treatability of Pre-Coagulated Slaughterhouse Wastewater Using Dead-End Filtration(Wiley, 2021-03-15) Ozdemir, Safiye; Uzal, Nigmet; Gokcek, Oznur BegumBACKGROUND In the present study, the performance of the membrane process, one of the advanced treatment methods that can enable the reuse of slaughterhouse wastewater, was evaluated. The wastewater was treated using ultrafiltration (UF) (10, 50 kDa), nanofiltration (NF) (150-300 DA) and reverse osmosis (RO) (500 kDa) membranes alone, and UF + NF, UF + RO membrane combinations at different pressures. In addition to rejection and permeate flux considerations, it was attempted to select the most effective membrane by performing scanning electron microscopy, Fourier transform infrared, contact angle, and atomic force microscopy analyses of the membranes used. RESULTS As a result of the experiments, the highest flux was observed at 5 bar for the 50 kDa UF membrane. When the performances of the sequential application of 10 and 50 kDa UF membranes followed by NF and RO membranes were evaluated, the highest flux was obtained for the sequential application of the 50 kDa UF membrane with the NF membrane as 19.68 and 9.05 L m(-2) h, respectively. CONCLUSION The highest chemical oxygen demand (COD) removal was obtained for the RO membrane at 20 bar as 88.67%, and for the 50 kDa UF + RO sequential application, the COD removal was increased from 70% to 88.67%. (c) 2021 Society of Chemical Industry (SCI).Article Citation - WoS: 11Citation - Scopus: 13Fabrication and Characterization of Silane-Functionalized Na-Bentonite Polysulfone/Polyethylenimine Nanocomposite Membranes for Dye Removal(Wiley, 2020-02-04) Saki, Seda; Senol-Arslan, Dilek; Uzal, NigmetIn this study, tetraethoxysilane (TEOS)-functionalized Na-bentonite incorporated into polysulfone/polyethylenimine (PSF/PEI) membranes were fabricated by phase inversion method for the efficient removal of methylene blue dye. For the preparation of PSF/PEI nanocomposite membranes, silane-functionalized Na-bentonite and pure Na-bentonite were used at three different concentrations (0.5, 1, and 2 wt%). The prepared membranes were characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, atomic force microscopy, porosity, hydrophilicity, and water permeability measurements. Antifouling behaviors and methylene blue dye rejections of the PSF/PEI nanocomposite membranes were also tested. The obtained results showed that the addition of pure Na-bentonite and silane-functionalized Na-bentonite both increased the water permeability of the membranes. The PSF/PEI membrane containing 2 wt% silane-functionalized Na-bentonite showed the highest water flux of 105 L m(-2) h(-1), while the lowest water flux of 1.2 L m(-2) h(-1) was recorded for pure PSF membrane. Filtration results demonstrated that the antifouling capacity was significantly increased due to the negatively charged surface of the newly generated silane-functionalized Na-bentonite PSF/PEI membranes. In summary, TEOS-functionalized Na-bentonite can be used to fabricate PSF/PEI nanocomposite membranes with effective filtration ability, antifouling capacity with lower decay ratio, higher flux recovery ratio, and 99% methylene blue dye removal performance.Article Citation - WoS: 9Citation - Scopus: 11Evaluation of Diatomite Substitute With Thermal Power Plant Waste Fly Ash in Sustainable Geopolymer Through Life Cycle Assessment(Springer, 2025-02-28) Ilkentapar, Serhan; Orklemez, Ezgi; Durak, Ugur; Gulcimen, Sedat; Bayram, Savas; Uzal, Nigmet; Atis, Cengiz DuranThis research demonstrates the potential of diatomite as a fly ash replacement to improve mechanical properties and environmental sustainability and presents it as a viable alternative for sustainable construction. Additionally, a life cycle assessment (LCA) was conducted on the produced mortars to quantitatively compare their environmental impacts using a cradle-to-gate approach. In mixtures, it was used by replacing the diatomite in the ratios of 1%, 2%, 3%, 4%, and 5% by weight of the fly ash. Workability, unit weight, flexural and compressive strength, abrasion resistance, elevated temperature resistance and microstructure analysis were carried out. The results indicated that replacing 1%, 2%, and 3% diatomite increased the compressive and flexural strength of mortars due to their higher specific surface area. Two percent replacement of diatomite provided the best results. FESEM results of 3% diatomite inclusion showed more intense and compact microstructure of geopolymer. Diatomite inclusion increased the abrasion resistance of geopolymer. Since 2% diatomite replacement was found to be optimum, the LCA results showed that geopolymer mortar with 2% diatomite has 25% lower impacts in terms of global warming potential and 10% lower impacts in terms of terrestrial ecotoxicity than conventional Portland cement mortar.Article Efficiency of L-DOPA+TiO2 Modified RO Membrane on Salinity Gradient Energy Generation by Pressure Retarded Osmosis(Pamukkale Univ, 2024) Ates, Nuray; Saki, Seda; Gokcek, Murat; Uzal, NigmetHarvesting energy from the salinity gradient of seawater and river water using pressure retarded osmosis (PRO) has been a major research topic of recent years. However, there is a need for efficient PRO membranes that can generate high power density and are pressure resistant, as the performance of current membranes on the market is poor. In this study, specific energy potential of PRO process using LDOPA+TiO2 modified BW30-LE membrane was evaluated on synthetic and real water samples. Polyamide BW30-LE RO membrane was modified by L-DOPA, L-DOPA+0.5 wt% TiO2 and L-DOPA+1 wt% TiO2. The effect of hydraulic pressure and temperature on generation of power density were evaluated for 5, 10, and 15 bar pressures, as well as 10 degrees C, 20 degrees C, and 30 degrees C degrees. The incorporation of TiO2 nanoparticles with L-DOPA increased the water flux by increasing the surface hydrophilicity and roughness of the membrane surface. The maximum specific power was observed as 1.6 W/m(2) for L-DOPA+1 wt% TiO2 modified BW30-LE membrane at 15 bar pressure. Besides, Mediterranean and Aegean, Black Sea water samples were used as draw solution and Seyhan, Ceyhan, Buyuk Menderes, Gediz, Yesilirmak, and Kizilirmak Rivers were used as feed solution. The highest osmotic power density was obtained by using L-DOPA+1 wt% TiO2 modified BW30-LE membrane with Ceyhan River as feed and Mediterranean Sea water as draw solution, which have the highest differences in salinity. In the mixture of Mediterranean and Ceyhan River, the highest power density was obtained at 10 bar pressure at 30 +/- 5 degrees C with 0.70 W/m(2).Article Citation - WoS: 12Citation - Scopus: 14Developing a Decision-Support System for Waste Management in Aluminum Production(Springer, 2016-04-13) Ozmen, Mihrimah; Aydogan, Emel Kizilkaya; Ates, Nuray; Uzal, NigmetIndustrial enterprises constitute a major portion of the world's economy, as well as a large proportion of a country's businesses and total employment. In Turkey, industrial enterprises are underdeveloped in terms of knowledge, skill, capital, and particularly accessing and benefiting from the advantages provided by modern information and communication technologies. Aluminum manufacturing has been reported to be the largest industry in Turkey with respect to production volumes and application fields. However, aluminum production is known to be an important contributor to environmental pollution, and the relative contribution of other related enterprises to the total industrial environmental impact is unknown. Environmental pollution sources can typically be classified into three categories: gaseous emissions, solid wastes, and wastewaters. The types of wastes produced by aluminum production vary based on the process line used, the variety of target products produced, and the production capacity of a given plant. As the capacities of facilities grow, the type and amount of waste become more variable. Therefore, the primary objective of this study is to determine the priority of each waste type in aluminum manufacturing industries. This study was conducted in the Industrial Zone of Kayseri in Turkey. Three different facilities that range in size from large to small based on their production volume, plant capacity, and variety of production are selected for this study. The priority of waste types was determined by combining the AHP and PROMETHEE II multicriteria decision methods. While wastewater was categorized as having the highest priority in large facilities, solid waste was determined to be the highest priority in medium and small facilities.Article Citation - WoS: 6Citation - Scopus: 6Comparative Life Cycle Assessment of Retort Pouch and Aluminum Can for Ready-to Bean Packaging(Springer, 2023-09-12) Gulcimen, Sedat; Ozcan, Ozlem; Cevik, Selin Babacan; Kahraman, Kevser; Uzal, NigmetSince packaging contributes to severe environmental impacts in food production, alternatives of packaging materials that satisfy customer needs while minimizing environmental impacts in a cost-effective manner should be preferred for food product sustainability. This paper compares two different packaging materials (aluminum cans and retort pouches) with a life cycle approach to assess the environmental impacts of ready-to-eat bean packaging. The life cycle assessment (LCA) was used to define and compare the environmental performance of ready-to-eat beans in aluminum cans and retort pouches. The gate-to-gate approach was used in the LCA, with a functional unit of 1 kg of packaged ready-to-eat bean product. Inventory for packaging in retort pouch was created in collaboration with Duru Bulgur Company (Karaman, Turkey) and the data for ready-to-eat beans in the aluminum can were gathered from the literature. The findings show that ready-to-eat beans in retort pouches have lower environmental impacts than ready-to-eat beans in aluminum cans. The packaging and washing processes for both ready-to-eat beans packaged in aluminum cans and retort pouches had the greatest environmental impact. In ready-to-eat beans production, retort pouch provides 87% better environmental performance than aluminum can in terms of global warming (GW). Overall, the results demonstrated that replacing aluminum cans with retort pouches in ready-to-eat bean production can significantly reduce environmental effects in all impact categories. [Graphics] .Article Citation - WoS: 13Citation - Scopus: 16Clarification of Pomegranate Juice Using PSF Microfiltration Membranes Fabricated With Nano TiO2and Al2O3(Wiley, 2020-06-22) Severcan, Solmaz Sebnem; Uzal, Nigmet; Kahraman, KevserMicrofiltration (MF) membranes were fabricated using PSF/PEI (17/2 wt%) with TiO(2)and Al(2)O(3)nanoparticles to enhance pomegranate juice clarification performance. The membrane performances were tested using dead-end filtration system. Membranes were characterized by Scanning Electron Microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), porosity, water contact angle, and pure water flux experiments. All MF membranes had higher porosity, pure water flux, and hydrophilicity.SEMimages of the membranes proved the nanoparticle incorporation to the PSF/PEI matrix. The quality of clarified pomegranate juice samples using PSF/PEI nanocomposite membranes were better than that of clarified using both commercial and unmodified membranes. The highest performance for the clarification of pomegranate juice samples was obtained for 0.05% of Al(2)O(3)incorporated PSF/PEI membranes with the highest color (5,781 +/- 4 PtCo), total soluble solid (16.2 +/- 0.0 Brix), total phenolic content (2,642.1 +/- 46.4 mg GAE/L), antioxidant activity (ABTS: 62.4 +/- 0.2 TEAC/L, DPPH: 41.3 +/- 0.0 TEAC/L) and total monomeric anthocyanin (100.7 +/- 1.7 mg/L). Practical applications Utilization of membrane technology in food industry has been increased rapidly in the past two decades. Due to their advantage in terms of saving color pigments, MF membranes are more suitable than UF ones for clarification of pomegranate juice. Incorporation of nanoparticles to the membrane matrix is one of the methods to increase the antifouling character and the strength of the membranes modified with hydrophilic polymers. There are some studies investigating the effect of TiO(2)and Al(2)O(3)nanoparticles on the properties of polymeric membranes. However, there are no reported data on the utilization of TiO(2)and Al(2)O(3)nanocomposite membranes for clarifying pomegranate juice. In this study, TiO(2)and Al(2)O(3)incorporated new generation PSF/PEI membranes were utilized in the clarification process of pomegranate juice for the first time in the literature. The results showed that Al(2)O(3)incorporation seems to be a good alternative for clarifying pomegranate juice with enhanced quality parameters.