WoS İndeksli Yayınlar Koleksiyonu
Permanent URI for this collectionhttps://hdl.handle.net/20.500.12573/394
Browse
5 results
Search Results
Article Citation - WoS: 22Citation - Scopus: 26Microstructure and Mechanical Properties of Dense Si3N4 Ceramics Prepared by Direct Coagulation Casting and Cold Isostatic Pressing(Elsevier Science SA, 2022-09) Marulcuoglu, Hande; Kara, FerhatComplex shaped dense Si3N4 ceramics were produced by using direct coagulation casting technique via dispersant reaction method of Si3N4 suspension, followed by gas pressure sintering. The effects of solid content of the suspension, additional cold isostatic pressing of the cast parts, and sintering behaviour and on the mechanical reliability of silicon nitride ceramics were investigated. It was observed that all slurries exhibited rheological properties suitable for casting in the range of 44-50 vol.% solid concentrations. Nevertheless, higher solid concentration suspensions resulted in smaller floc size and thus better green microstructures. Parts shaped by direct coagulation casting at all the solid loadings had relatively low strength and reliability after sintering. However, application of additional cold isostatic pressing to the cast parts increased the strength and, particularly, reliability. Dense Si3N4 ceramics with relative density above 99.5%, average bending strength 760 +/- 39 MPa and Weibull module 23.5 had been obtained with 50 vol.% solids content after DCC + CIP process.Article Citation - WoS: 36Citation - Scopus: 37Histopathological and Biomechanical Evaluation of Tenocyte Seeded Allografts on Rat Achilles Tendon Regeneration(Elsevier Sci Ltd, 2015-05) Gungormus, Cansin; Kolankaya, Durdane; Aydin, ErkinTendon injuries in humans as well as in animals' veterinary medicine are problematic because tendon has poor regenerative capacity and complete regeneration of the ruptured tendon is never achieved. In the last decade there has been an increasing need of treatment methods with different approaches. The aim of the current study was to improve the regeneration process of rat Achilles tendon with tenocyte seeded decellularized tendon matrices. For this purpose, Achilles tendons were harvested, decellularized and seeded as a mixture of three consecutive passages of tenocytes at a density of 1 x 10(6) cells/ml. Specifically, cells with different passage numbers were compared with respect to growth characteristics, cellular senescence and collagen/tenocyte marker production before seeding process. The viability of reseeded tendon constructs was followed postoperatively up to 6 months in rat Achilles tendon by histopathological and biomechanical analysis. Our results suggests that tenocyte seeded decellularized tendon matrix can significantly improve the histological and biomechanical properties of tendon repair tissue without causing adverse immune reactions. To the best of our knowledge, this is the first long-term study in the literature which was accomplished to prove the use of decellularized matrix in a clinically relevant model of rat Achilles tendon and the method suggested herein might have important implications for translation into the clinic. (C) 2015 Elsevier Ltd. All rights reserved.Article Citation - WoS: 31Citation - Scopus: 33Determination of Stress-Strain Relationship Based on Alkali Activator Ratios in Geopolymer Concretes and Development of Empirical Formulations(Elsevier Science Inc, 2023-02) Ozbayrak, Ahmet; Kucukgoncu, Hurmet; Atas, Oguzhan; Aslanbay, Huseyin Hilmi; Aslanbay, Yuksel Gul; Altun, FatihFly ash-based geopolymer has recently gained attention of researchers due to its potential application, as well as being an alternative binder with low emissions compared to ordinary Portland cement (OPC) in concrete production. Studies which are conducted on the design and mechanical properties of structural members produced from fly ash geopolymer concrete (GPC) are very important in terms of increasing the use of this concrete. The aim of this study is to obtain experimental data on the effect of sodium silicate/sodium hydroxide (SS/SH) and alkali activators/fly ash (AA/FA) ratios on the mechanical properties of a low calcium heat-cured fly ash geopolymer. In addition, it is to reveal the similarities and differences of OPC and GPC by comparing the mathematical formulations in existing regulations and concrete models with experimental data. Thus, geopolymer cylinder concrete samples were produced using 15 different mixtures with SS/SH ratios of 1.5, 2.5 and 3.5, while AA/FA ratios of 0.4, 0.5, 0.6, 0.7 and 0.8. At the end of the study, the optimum SS/SH ratio was obtained as 2.5. A decrease in the AA/FA ratio increases the compressive and splitting tensile strength, while an increment increases the ductility and consuming energy. In addition, the relationship between the experimental data and the splitting tensile strength and modulus of elasticity formulations depending on the compressive strength given in other studies and regulations as a part of literature was investigated, and then, two alternative empirical formulations considering the ratios of alkali activators were proposed at the end of the regression analysis. When the stress-strain relationship of OPC concrete models and GPC mixtures were compared, the closest unconfined concrete model for GPC concrete was the Hognestad model.Article Citation - WoS: 81Citation - Scopus: 91Alkali Activation of Mortars Containing Different Replacement Levels of Ground Granulated Blast Furnace Slag(Elsevier Sci Ltd, 2012-03) Bilim, Cahit; Atis, Cengiz Duran; Ati, Cengiz DuranThe aim of the present study is to investigate some properties of alkali-activated mortars containing slag at different replacement levels. Ground granulated blast furnace slag was used at 0%, 20%, 40%, 60%, 80% and 100% replacement by weight of cement, and liquid sodium silicate having three different Na dosages was chosen as the alkaline activator. In this research, carbonation resistance measurements and compressive and flexural strength tests were performed on the mortar specimens with size of 40 x 40 x 160 mm. The findings obtained from the tests showed that carbonation depth values of the mortars decreased with the increase of activator dosage. Additionally, compressive and flexural strength values increased with the increase in activator concentration and slag replacement level. Portland cement/slag mortars activated by liquid sodium silicate exhibited lower strength than the slag alone activated by the same activator. (C) 2011 Elsevier Ltd. All rights reserved.Article Citation - WoS: 53Citation - Scopus: 55Comprehensive Experimental Analysis of the Effects of Elevated Temperatures in Geopolymer Concretes With Variable Alkali Activator Ratios(Elsevier, 2023) Ozbayrak, Ahmet; Kucukgoncu, Hurmet; Aslanbay, Huseyin Hilmi; Aslanbay, Yuksel Gul; Atas, OguzhanBy growing population and rapid urbanization, demand for concrete increases exponentially. Researches on use of fly ash material in waste product class for concrete production are important to produce concrete more environmentally friendly. However, there is a need for more research to use geopolymer concrete (GPC) in every field where ordinary Portland cement concrete (OPC) is used. Therefore, it is crucial to experimentally investigate thermal properties as well as me-chanical properties of geopolymer concrete. As investigated thermal properties, the main factor affecting strength development of GPC is alkali activator ratios. In this study, GPC prism samples with nine different compositions, produced by various alkali ratios. After flexural strength tests, they were cut into cubes and exposed to 400 degrees C, 600 degrees C and 800 degrees C, then they were subjected to compressive strength tests. Results obtained from different AA/FA and SS/SH ratios were eval-uated as mechanical properties at ambient temperature and physical, mechanical and micro-structural properties at elevated temperature. An empirical formula, which considers the effect of activator ratios, was proposed to calculate flexural strength depending on compressive strength of samples at ambient temperature. As an increase of SS/SH and AA/FA ratios, compressive strength increased, while flexural strength decreased. The increase in AA/FA ratio decreased compressive strength of samples exposed to high temperatures, while increase in SS/SH ratio did not deter-mine at elevated temperatures. There is an inverse change with AA/FA ratio and parallel change with SS/SH ratio between compressive strengths of samples at ambient temperature and exposed to high temperature.