WoS İndeksli Yayınlar Koleksiyonu
Permanent URI for this collectionhttps://hdl.handle.net/20.500.12573/394
Browse
3 results
Search Results
Article Citation - WoS: 14Citation - Scopus: 16Dynamic Soil Characterization and Site Response Estimation for Erbaa, Tokat (Turkey)(Springer, 2016-03-11) Akin, Muge K.; Kramer, Steven L.; Topal, TamerSite amplification is one of the most important factors controlling damage in urban areas through strong earthquakes. Local site effects play an important role in earthquake-resistant design and should be considered for site response analyses. In this study, ground response analyses in Erbaa, Turkey, a settlement in the North Anatolian Fault Zone, using one-dimensional equivalent linear analysis and empirical approaches based on shear wave velocity profiles are evaluated and compared. The ground response analyses were performed with consideration of shear wave velocity, and modulus reduction and damping behavior for different confining pressure and plasticity index-dependent models. The results of ground response analyses and amplification values from empirical equations using shear wave velocity are illustrated in terms of amplification and predominant period maps of the seismically active Erbaa settlement area. The comparison has been made in these produced maps of the study area in order to evaluate different site response analyses.Article Citation - WoS: 30Citation - Scopus: 33Assessment of the Effectiveness of a Rockfall Ditch Through 3-D Probabilistic Rockfall Simulations and Automated Image Processing(Elsevier, 2021-03) Akin, Mutluhan; Dincer, Ismail; Ok, Ali Ozgun; Orhan, Ahmet; Akin, Muge K.; Topal, TamerRockfall ditches or catchment areas aim to collect falling blocks at the toe of a source zone by dissipating the energy of blocks in an excavated trench. The effectiveness of a rockfall ditch is simply expressed by its block catchment performance and can be evaluated by empirically using existing design charts as well as rockfall simulations. Although 2-dimensional (2-D) analysis has been executed to assess the catchment ditch effectiveness in engineering practice, 3-dimensional (3-D) rockfall models have not received enough attention so far. In this study, the effectiveness of a considerably long rockfall ditch to protect a settlement from falling rocks was assessed on the basis of 3-D rockfall analyses executed using high-resolution digital surface models. The rockfall ditch efficiency was found to be moderate to limited for various segments considering the percentage of blocks not trapped by the ditch. Moreover, the sensitivity of ditch efficiency to ditch depth was analyzed by automated image processing method as well. Additionally, a particular section of ditch alignment was fictitiously excavated or filled by synthetic Digital Surface Model (DSM) generation through image processing. 3-D rockfall modeling carried out using the DSMs with synthetically manipulated ditches points out that the effectiveness of a catchment ditch is highly depended upon ditch depth. Even a small volume of block accumulation inside the ditch definitely reduces the ditch performance resulting extended runout distances reaching to residential area. Finally, 3-D rockfall modeling is accepted to be an effective tool to rate the efficiency of existing rockfall ditches and synthetically generated ditches on DSMs (or DEMs) by means of automated image processing method may assist the control of current ditch dimension as well as new catchment ditch design.Article Citation - WoS: 8Citation - Scopus: 9A New Quantitative Welding Degree Classification for Ignimbrites(Springer, 2023-06-28) Akin, Mutluhan; Topal, Tamer; Dincer, Ismail; Akin, Muge K.; Ozvan, Ali; Orhan, Ahmet; Orhan, AyseAs a pyroclastic rock type, ignimbrites may reveal varying degrees of welding depending on the temperature (> 535 celcius) and overburden pressure conditions during its formation. The welding degree of ignimbrites increases as the formation temperature and the thickness of the overburden deposit in the depositional environment escalate, which are the most crucial factors controlling the rate of welding in ignimbrites. With the increasing temperature, plastic deformation is observed in ignimbrites and the glassy minerals are being welded. Furthermore, the thickness of the overburden causes the deformation of the ash matrix in ignimbrites at the lower sections and the pumice grains are flattened at different rates. An increase in the degree of welding of ignimbrites causes an improvement in the physical and mechanical properties of the rock material as well. Within the scope of this research, petrographical, mineralogical, and geochemical studies were carried out on a total of 16 different ignimbrite types, which have different color and texture properties, obtained from three different regions of Turkey (Kayseri, Nevsehir, Ahlat) where ignimbrites extensively crop out, and the physical and mechanical properties of these samples were revealed. Consequently, a new welding classification was developed for ignimbrites considering the uniaxial compressive strength and dry unit weight. The proposed welding classification consists of six classes ranging from non-welded to highly welded. When the welding degrees of the selected ignimbrites are evaluated, Kayseri ignimbrites mostly exhibit moderate welding characteristics. Nevsehir ignimbrites, on the other hand, have a low welding degree whereas the degree of welding in Ahlat ignimbrites may vary from low to high. Additionally, long and short axis lengths of pumice grains in the ignimbrite specimens were determined by measuring under the microscope, and shape ratios were determined by different shape parameter evaluation methods. As a result, it has been concluded that the pumice grains in Kayseri and Ahlat ignimbrites have a more lenticular structure than the pumice grains in Nevsehir ignimbrites. Eventually, the welding degree classes of ignimbrites and the classification developed by using threshold values of the oblateness ratio (OR) values of pumice grains at different welding degrees are quite compatible. The proposed welding degree classification is of great importance in the selection of ignimbrites widely used as dimension stone and in terms of engineering classification of this rock type as well as it will guide to the scientific studies to be performed on ignimbrites with varying physical and mechanical properties.