WoS İndeksli Yayınlar Koleksiyonu
Permanent URI for this collectionhttps://hdl.handle.net/20.500.12573/394
Browse
25 results
Search Results
Article Tuning Mechanical Performance of PCL Scaffolds: Influence of 3D Bioprinting Parameters, Polymer Concentration, and Solvent Selection(IOP Publishing Ltd, 2025-09-01) Ceylan, Saniye Aylin; Baltacioglu, Mehmet Furkan; Bal, Burak; Bayram, Ferdi Caner; Isoglu, Ismail AlperThe mechanical performance of three-dimensional (3D) bioprinted scaffolds is susceptible to printing parameters and material formulation. In this study, poly (epsilon-caprolactone) (PCL) scaffolds were fabricated using four different polymer concentrations (10%, 25%, 50%, and 75% w/v) to investigate how these variations, along with process parameters, influence mechanical behavior. Maintaining the structural integrity of bioprinted constructs requires careful optimization of polymer concentration and precise control over parameters such as printing speed, pressure, and infill density. Tensile tests were conducted to evaluate the effects of these variables. Among the tested conditions, a 50% (w/v) concentration allowed for a broader operational window, enabling fabrication across a range of printing speeds and pressures. At a printing speed of 5 mm s-1, PCL-DCM exhibited a Young's modulus of 39.0 MPa, while PCL-CF samples printed at 10 mm s-1 achieved the highest modulus of 32.0 MPa. Notably, when the printing speed was kept constant, applying higher pressures led to an increase in Young's modulus, suggesting that pressure plays a key role in enhancing scaffold stiffness. When comparing the 50% and 75% (w/v) polymer concentrations, the 50% (w/v) formulation stood out by offering both higher elongation and greater stiffness, which makes it particularly suitable for load-bearing applications. These findings provide a quantitative framework for optimizing extrusion-based bioprinting of PCL scaffolds, with implications for customized biomedical implants and regenerative medicine.Article Citation - WoS: 1Citation - Scopus: 1Prediction of the Diffusible Hydrogen Concentration After Electrochemical Charging Utilizing Artificial Intelligence(IOP Publishing Ltd, 2025-09-01) Sivesoglu, Abdurrahman; Li, Yang; Bal, BurakThe concentration of diffusible hydrogen in a material is of high importance as it helps to predict the hydrogen embrittlement effect in the material, and the amount of mechanical properties' degradation after reaching a critical concentration. Despite that, a simple experimental setup is not available to measure hydrogen concentration at service. In this paper, a multi-layer perceptron (MLP) model is developed using weight initialization, which can estimate the diffusible hydrogen concentration of Face-Centred-Cubic (FCC) metals after electrochemical charging. The input properties of the model include the electrochemical charging parameters of current density, temperature, and charging time as well as the grain size of the specimen. The MLP model with and without the weight initialization was validated and tested with unseen test dataset. The model in both cases showed an excellent predictive performance with a higher accuracy and faster convergence when using weight initialization. A linear correlation of 89% between the experimental and predicted hydrogen concentration was observed. This demonstrates that for the family of FCC metals under electrochemical charging, the estimation of diffusible hydrogen concentration is a feasible path for material safety design analysis.Article Citation - WoS: 40Citation - Scopus: 43The Role of Hydrogen in the Edge Dislocation Mobility and Grain Boundary-Dislocation Interaction in Α-Fe(Pergamon-Elsevier Science Ltd, 2021-09) Kapci, Mehmet Fazil; Schoen, J. Christian; Bal, Burak; Schön, J. ChristianThe atomistic mechanisms of dislocation mobility depending on the presence of hydrogen were investigated for two edge dislocation systems that are active in the plasticity of alpha-Fe, specifically 1/2<111>{110} and 1/2<111>{112}. In particular, the glide of the dislocation pile-ups through a single crystal, as well as transmission of the pile-ups across the grain boundary were evaluated in bcc iron crystals that contain hydrogen concentrations in different amounts. Additionally, the uniaxial tensile response under a constant strain rate was analyzed for the aforementioned structures. The results reveal that the presence of hydrogen decreases the velocity of the dislocations -in contrast to the commonly invoked HELP (Hydrogen-enhanced localized plasticity) mechanism-, although some localization was observed near the grain boundary where dislocations were pinned by elastic stress fields. In the presence of pre-exisiting dislocations, hydrogen-induced hardening was observed as a consequence of the restriction of the dislocation mobility under uniaxial tension. Furthermore, it was observed that hydrogen accumulation in the grain boundary suppresses the formation of new grains that leads to a hardening response in the stress-strain behaviour which can initiate brittle fracture points. (C) 2021 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.Article Citation - WoS: 13Citation - Scopus: 14The Effect of Strain Rate on the Hydrogen Embrittlement Susceptibility of Aluminum 7075(ASME, 2022-11-22) Baltacioglu, Mehmet Furkan; Cetin, Baris; Bal, BurakThe effects of changing the strain rate regime from quasi-static to medium on hydrogen susceptibility of aluminum (Al) 7075 were investigated using tensile tests. Strain rates were selected as 1 s(-1) and 10(-3) s(-1) and tensile tests were conducted on both hydrogen uncharged and hydrogen charged specimens at room temperature. Electrochemical hydrogen charging method was utilized and the diffusion length of hydrogen inside Al 7075 was modeled. Material characterizations were carried out by X-ray diffraction (XRD) and energy dispersive X-ray spectroscopy (EDX) and microstructural observations of hydrogen uncharged and hydrogen charged specimens were performed by scanning electron microscope (SEM). As opposed to earlier studies, hydrogen embrittlement (HE) was more pronounced at high strain rate cases. Moreover, hydrogen enhanced localized plasticity (HELP) was the more dominant hydrogen embrittlement mechanism at slower strain rate but coexistence of hydrogen enhanced localized plasticity and hydrogen enhanced decohesion was observed at a medium strain rate. Overall, the current findings shed light on the complicated hydrogen embrittlement behavior of Al 7075 and constitute an efficient guideline for the usage of Al 7075 that can be subject to different strain rate loadings in service.Article Citation - WoS: 23Citation - Scopus: 24Strain Rate and Hydrogen Effects on Crack Growth From a Notch in a Fe-High Steel Containing 1.1 Wt% Solute Carbon(Pergamon-Elsevier Science Ltd, 2020-01) Najam, Hina; Koyama, Motomichi; Bal, Burak; Akiyama, Eiji; Tsuzaki, KaneakiEffects of strain rate and hydrogen on crack propagation from a notch were investigated using a Fe-33Mn-1.1C steel by tension tests conducted at a cross head displacement speeds of 10(-2) and 10(-4) mm/s. Decreasing cross head displacement speed reduced the elongation by promoting intergranular crack initiation at the notch tip, whereas the crack propagation path was unaffected by the strain rate. Intergranular cracking in the studied steel was mainly caused by plasticity-driven mechanism of dynamic strain aging (DSA) and plasticity-driven damage along grain boundaries. With the introduction of hydrogen, decrease in yield strength due to cracking at the notch tip before yielding as well as reduction in elongation were observed. Coexistence of several hydrogen embrittlement mechanisms, such as hydrogen enhanced decohesion (HEDE) and hydrogen enhanced localized plasticity (HELP) were observed at and further away from the notch tip resulting in hydrogen assisted intergranular fracture and cracking which was the key reason behind the ductility reduction. (C) 2019 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.Article Citation - WoS: 11Citation - Scopus: 13On the Detailed Mechanical Response Investigation of PHBV/PCL and PHBV/PLGA Electrospun Mats(IOP Publishing Ltd, 2019-03-29) Bal, Burak; Tugluca, Ibrahim Burkay; Koc, Nuray; Isoglu, Ismail AlperIn this study, electrospun mats of pristine poly(epsilon-caprolactone) (PCL), Poly(D, L-lactide-co-glycolide) (PLGA), poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV), as well as PHBV/PCL blends and PHBV/PLGA blends in different ratios (80:20, 75:25, 50:50, 25:75, 20:80, 10:90, 5:95%, w/w) and Centella Asiatica (CA) loaded (1, 5, 10%, w/v) PHBV/PCL and PHBV/PLGA polyester blends were prepared. Electrospun mats were characterized by scanning electron microscopy (SEM) in order to show uniform and bead and defect-free fiber structure with average diameter. The blend ratio and strain rate dependencies of mechanical behavior of these electrospun membranes were investigated under tensile loading. The tensile tests were conducted at an initial strain rates of 10(-1) s(-1), 10(-2) s(-1), 10(-3) s(-1) and 10(-4) s(-1) at room temperature and the best and worst combinations of PHBV/PLGA, PHBV/PCL blend ratios for both stress and ductility required applications were specified for each strain rate. The effects of blend ratios on the tensile strength and Young's modulus were also investigated. Moreover, the effects of Centella Asiatica on the electrospun membranes' mechanical behavior were demonstrated at different strain rates. Consequently, this study constitutes an important guideline for the selection and usage of the aforementioned electrospun membranes as a wound dressing material in terms of mechanical response at different loading scenarios.Article Citation - WoS: 2Citation - Scopus: 2Numerical Investigation of the Role of Volumetric Transformation Strain on the Relaxation Stress and the Corresponding Hydrogen Interstitial Concentration in Niobium Matrix(Hindawi Ltd, 2017) Bal, BurakThe effects of relaxation stress on the hydrogen concentration in Niobium-(Nb-) H media were investigated by iterative numerical modeling approach. To calculate the transformation strain, relaxation stress, and corresponding relaxed hydrogen concentration around an edge dislocation, a new third-order polynomial formulation was utilized in the model. With the aid of this polynomial, hydrogen induced relaxation stress never exceeds the dislocation stress, which indicates that the total stress field never turns to compressive state and diverges the results. The current model calculates the hydrogen concentration not only in the vicinity of an edge dislocation but also far away from the dislocation. Furthermore, the effect of relaxation stress on the interaction energy was also captured in the model. Overall, the current findings shed light on the complicated hydrogen embrittlement mechanisms of metallic materials by demonstrating that hydrogen induced relaxation has a significant effect on the hydrogen atom concentration and the interaction energy between the existing internal stress field and the solute hydrogen atom.Article Citation - WoS: 14Citation - Scopus: 16Lowering Strain Rate Simultaneously Enhances Carbon- and Hydrogen-Induced Mechanical Degradation in an Fe-33Mn Steel(Springer, 2019-01-02) Tugluca, Ibrahim Burkay; Koyama, Motomichi; Shimomura, Yusaku; Bal, Burak; Canadinc, Demircan; Akiyama, Eiji; Tsuzaki, KaneakiWe investigated the strain rate dependency of the hydrogen-induced mechanical degradation of Fe-33Mn-1.1C steel at 303K within the strain rate range of 10(-2) to 10(-5)s(-1). In the presence of hydrogen, lowering the strain rate monotonically decreased the work hardening rate, elongation, and tensile strength and increased the yield strength. Lowering the strain rate simultaneously enhanced the plasticity-related effects of hydrogen and carbon, leading to the observed degradation of the ductility.Article Citation - WoS: 14Citation - Scopus: 15Lateral Angular Co-Extrusion: Geometrical and Mechanical Properties of Compound Profiles(MDPI, 2020-08-28) Thuerer, Susanne Elisabeth; Peddinghaus, Julius; Heimes, Norman; Bayram, Ferdi Caner; Bal, Burak; Uhe, Johanna; Klose, Christian; Thürer, Susanne ElisabethA novel co-extrusion process for the production of coaxially reinforced hollow profiles has been developed. Using this process, hybrid hollow profiles made of the aluminum alloy EN AW-6082 and the case-hardening steel 20MnCr5 (AISI 5120) were produced, which can be forged into hybrid bearing bushings by subsequent die forging. For the purpose of co-extrusion, a modular tooling concept was developed where steel tubes made of 20MnCr5 are fed laterally into the tool. This LACE (lateral angular co-extrusion) process allows for a variation of the volume fraction of the reinforcement by using steel tubes with different wall thicknesses, which enabled the production of compound profiles having reinforcement contents of either 14 vol.% or 34 vol.%. The shear strength of the bonding area of these samples was determined in push-out tests. Additionally, mechanical testing of segments of the hybrid profiles using shear compression tests was employed to provide information about the influence of different bonding mechanisms on the strength of the composite zone.Article Citation - WoS: 3Citation - Scopus: 3Investigations of Strain Rate, Size, and Crack Length Effects on the Mechanical Response of Polycaprolactone Electrospun Membranes(Sage Publications Ltd, 2021-06-18) Bayram, Ferdi C.; Kapci, Mehmet F.; Yuruk, Adile; Isoglu, Ismail A.; Bal, BurakThe effects of strain rate, size (height x width), and pre-existing crack length on the mechanical response of polycaprolactone electrospun membranes were investigated by tension tests conducted at room temperature. In particular, tensile tests were performed with three different strain rates for strain rate effect tests, seven different geometries for elucidating the size effect, and three different initial notch lengths for crack growth experiments. The electrospun membranes were produced by the electrospinning technique using a polycaprolactone solution prepared in 1, 1, 1, 3, 3, 3-hexafluoro-2-propanol as the solvent. Scanning electron microscopy was utilized to show the continuous fiber structure without bead formation. The average fiber diameter was calculated as 1.113 +/- 0.270 mu m by using scanning electron microscopy images of the membranes. The chemical structure of polycaprolactone was analyzed by Fourier transform infrared spectroscopy, and the toxicity and cell viability of the electrospun membranes were shown by CellTiter 96(R) Aqueous One Solution Cell Proliferation Assay (MTS test). It was observed that the ultimate tensile strength and Young's modulus decreased, and the elongation at failure value increased as the strain rate decreased from 10(-1) to 10(-3) s(-1). Besides, positive strain rate sensitivity was observed on the mechanical response of electrospun polycaprolactone membranes. Moreover, the dependency of mechanical response on the size geometry has been well studied, and the optimum height and width combinations were specified. Also, crack growth was studied in terms of both macroscopic and microstructural deformation mechanisms and it is observed that individual fiber deformations and interactions are highly effective on the mechanical behavior and also propagation of the crack. Consequently, in this study, the size and strain rate effects and crack growth on the mechanical response of electrospun polycaprolactone membranes have been investigated extensively, and the results presented herein constitute an essential guideline for the usage of polycaprolactone electrospun membranes at different loading scenarios.
- «
- 1 (current)
- 2
- 3
- »