Browsing by Author "Saki, Seda"

Now showing 1 - 7 of 7

Efficiency of L-DOPA+TiO2 modified RO membrane on salinity gradient energy generation by pressure retarded osmosis
(Pamukkale Üniversitesi, 2024) Ateş, Nuray; Saki, Seda; Gokcek, Murat; Uzal, Niğmet; 0000-0001-8923-2323; 0000-0002-0912-3459; AGÜ, Fen Bilimleri Enstitüsü, Malzeme Bilimi ve Makine Mühendisliği Ana Bilim Dalı; SAKİ, Seda; Uzal, Niğmet
Harvesting energy from the salinity gradient of seawater and river water using pressure retarded osmosis (PRO) has been a major research topic of recent years. However, there is a need for efficient PRO membranes that can generate high power density and are pressure resistant, as the performance of current membranes on the market is poor. In this study, specific energy potential of PRO process using LDOPA+TiO2 modified BW30-LE membrane was evaluated on synthetic and real water samples. Polyamide BW30-LE RO membrane was modified by L-DOPA, L-DOPA+0.5 wt% TiO2 and L-DOPA+1 wt% TiO2. The effect of hydraulic pressure and temperature on generation of power density were evaluated for 5, 10, and 15 bar pressures, as well as 10 °C, 20 °C, and 30 °C degrees. The incorporation of TiO2 nanoparticles with L-DOPA increased the water flux by increasing the surface hydrophilicity and roughness of the membrane surface. The maximum specific power was observed as 1.6 W/m2 for L-DOPA+1 wt% TiO2 modified BW30-LE membrane at 15 bar pressure. Besides, Mediterranean and Aegean, Black Sea water samples were used as draw solution and Seyhan, Ceyhan, Buyuk Menderes, Gediz, Yesilirmak, and Kizilirmak Rivers were used as feed solution. The highest osmotic power density was obtained by using L-DOPA+1 wt% TiO2 modified BW30-LE membrane with Ceyhan River as feed and Mediterranean Sea water as draw solution, which have the highest differences in salinity. In the mixture of Mediterranean and Ceyhan River, the highest power density was obtained at 10 bar pressure at 30 ± 5°C with 0.70 W/m2 .
Enhanced hydrophilicity and mechanical robustness of polysulfone nanofiber membranes by addition of polyethyleneimine and Al2O3 nanoparticles
(ELSEVIERRADARWEG 29, 1043 NX AMSTERDAM, NETHERLANDS, 2017) Uzal, Nigmet; Ates, Nuray; Saki, Seda; Bulbul, Y. Emre; Chen, Yongsheng; AGÜ, Mühendislik Fakültesi, İnşaat Mühendisliği Bölümü; Uzal, Nigmet
A novel hydrophilic and mechanically robust polysulfone (PSF) nanofiber membrane (NFM) was prepared by electrospinning of a PSF solution blended with polyethyleneimine (PEI) and Al2O3 nanoparticles. The influence of PEI and Al2O3 nanoparticles concentration on the NFM characteristics was studied using scanning electron microscopy (SEM), Fourier transform infrared FT-IR spectroscopy, porosity, water contact angle measurement, and tensile strength test. Filtration performance of the nanofiber membranes (NFMs) were evaluated by the measurement of pure water flux (PWF) and bovine serum albumin (BSA) rejection tests. According to the results, blending PSF solution with 2 wt.% PEI and 0.05 wt.% Al2O3 nanoparticles resulted in formation of NFMs with high porosity and increased mechanical strength, which exhibited a low water contact angle of 23.5 and high water flux of 28,456 L/m(2) h. On the other hand, incorporation of nanoparticles and PEI in the PSF membrane matrix led to increasing of tensile strength that it was changed from 0.15 to 0.69 for pure PSF and PSF/PEI/Al2O3, respectively. A-24 and 48% BSA rejection performances were obtained by nanoparticle incorporated PSF membranes. In conclusion, the studies strongly suggest that blending with hydrophilic additives of NFMs can enhance the hydrophilicity and mechanical strength of PSF membranes and these NFMs can be effectively used in water based membrane systems. (C) 2017 Elsevier B.V. All rights reserved.
Fabrication and characterization of silane-functionalized Na-bentonite polysulfone/polyethylenimine nanocomposite membranes for dye removal
(WILEY, 111 RIVER ST, HOBOKEN 07030-5774, NJ USA, 2020) Saki, Seda; Senol-Arslan, Dilek; Uzal, Nigmet; 0000-0002-0912-3459; AGÜ, Mühendislik Fakültesi, Malzeme Bilimi ve Nanoteknoloji Mühendisliği Bölümü
In this study, tetraethoxysilane (TEOS)-functionalized Na-bentonite incorporated into polysulfone/polyethylenimine (PSF/PEI) membranes were fabricated by phase inversion method for the efficient removal of methylene blue dye. For the preparation of PSF/PEI nanocomposite membranes, silane-functionalized Na-bentonite and pure Na-bentonite were used at three different concentrations (0.5, 1, and 2 wt%). The prepared membranes were characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, atomic force microscopy, porosity, hydrophilicity, and water permeability measurements. Antifouling behaviors and methylene blue dye rejections of the PSF/PEI nanocomposite membranes were also tested. The obtained results showed that the addition of pure Na-bentonite and silane-functionalized Na-bentonite both increased the water permeability of the membranes. The PSF/PEI membrane containing 2 wt% silane-functionalized Na-bentonite showed the highest water flux of 105 L m(-2) h(-1), while the lowest water flux of 1.2 L m(-2) h(-1) was recorded for pure PSF membrane. Filtration results demonstrated that the antifouling capacity was significantly increased due to the negatively charged surface of the newly generated silane-functionalized Na-bentonite PSF/PEI membranes. In summary, TEOS-functionalized Na-bentonite can be used to fabricate PSF/PEI nanocomposite membranes with effective filtration ability, antifouling capacity with lower decay ratio, higher flux recovery ratio, and 99% methylene blue dye removal performance.
Predicting potential of pressure retarded osmosis power for different estuaries in Turkey
(WILEY, 111 RIVER ST, HOBOKEN 07030-5774, NJ USA, 2019) Saki, Seda; Uzal, Nigmet; Gokcek, Murat; Ates, Nuray; 0000-0002-7951-4236; 0000-0002-8923-4852; 0000-0002-0912-3459; AGÜ, Yaşam ve Doğa Bilimleri Fakültesi, Moleküler Biyoloji ve Genetik Bölümü
Pressure retarded osmosis (PRO) is an alternative renewable energy source recovered from the salinity gradient between the fresh water (feed solution) and salty water (draw solution). In order to implement osmotic power, the site-specific characteristics including the river and sea salinity, annual flow rates, ecological restrictions were taken into account. This study revealed a comprehensive analysis for a theoretical potential of PRO process for different estuaries in Turkey. In this study, the power potential prediction of PRO process for the Ceyhan, Sakarya, and Meric Rivers were analyzed via Gibbs free energy calculations. The net annual energy production is projected to be 167, 164, and 208 GWh/y for Ceyhan, Sakarya, and Meric Rivers, respectively. Meric River has the highest energy production of 208 GWh/yr with 186 m(3)/s mean flow rate and 245 mg/L salinity. These results clearly show that Turkey's rivers having high salinity and flow rate are feasible and applicable for making the osmotic power plant economically. Thereby, it is providing essential direction to the improvement of its design, installation, and operation. The developed methodology for the evaluation of the osmotic power potential of other rivers can be considered as a basis to assess the whole potential on a worldwide level. (c) 2018 American Institute of Chemical Engineers Environ Prog, 38:e13085, 2019
Preparation and characterization of PSF/PEI/CaCO3 nanocomposite membranes for oil/water separation
(SPRINGER HEIDELBERG, TIERGARTENSTRASSE 17, D-69121 HEIDELBERG, GERMANY, 2018) Saki, Seda; Uzal, Nigmet; AGÜ, Mühendislik Fakültesi, İnşaat Mühendisliği Bölümü
Ultrafiltration (UF) is one of the significant advanced processes for oily wastewater treatment due to its clear advantages, for instance, ease in operation and efficient separation. The main drawback of these processes is the fouling problem and many researchers' effort on fabrication of high-performance membranes with higher hydrophilicity and antifouling properties. In this study, flat-sheet polysulfone (PSF)/polyethylenimine (PEI)/CaCO3 nanocomposite membranes were prepared by phase inversion method for oil/water emulsion separation. Structural properties of membranes were characterized by SEM, FT-IR, contact angle, tensile strength, and atomic force microscopy analysis. Increasing the CaCO3 nanoparticle loading exhibited the increased the water flux and BSA rejection. PSF/PEI/10 wt% CaCO3 nanocomposite membranes have 145 L/m(2) h water flux at 2 bar with a contact angle of 84 degrees and with 92% BSA rejection. All prepared CaCO3 nanocomposite membranes reached similar oil rejections at above 90%. Besides the higher water flux and oil removal efficiencies, 10 wt% of CaCO3 nanoparticle-blended PSF membranes has notable antifouling capacity with the highest flux recovery ratio (FRR) and lowest flux decay ratio (DR) values. The results showed that there is a great potential to use PSF/PEI/CaCO3 nanocomposite membranes for the treatment of oil water emulsions with higher permeability and antifouling capacity.
The size and concentration effects of Al2O3 nanoparticles on PSF membranes with enhanced structural stability and filtration performance
(DESALINATION PUBL36 WALCOTT VALLEY DRIVE, HOPKINTON, MA 01748, 2017) Saki, Seda; Uzal, Nigmet; Ates, Nuray; 0000-0002-8923-4852; AGÜ, Mühendislik Fakültesi, İnşaat Mühendisliği Bölümü
Nanocomposite membranes have attracted attention for their high permeability, rejection efficiency, and thermal and mechanical stability. In this study, novel flat-sheet polysulfone nanocomposite membranes were prepared by a phase inversion method with polyethylenimine and Al2O3 nanoparticles to increase the flux and hydrophilicity. Al2O3 nanoparticles were added to the membrane matrix to enhance the permeability, selectivity, and mechanical resistance. Two different sizes of Al2O3 nanoparticles (20 and 80 nm) were used with different weight percentages of 0.2, 1, and 5 wt%. The effects of the size and concentration of the nanoparticles on the structural properties and filtration performance of the membranes were investigated. Scanning electron microscopy, Fourier transform infrared spectroscopy, porosity, water contact angle, thermogravimetric analysis, viscosity, and tensile strength measurements were used to characterize the prepared membranes. The membrane performance was evaluated with water flux and bovine serum albumin rejection tests. According to the results, the membrane containing 15 wt% polysulfone, 1 wt% polyethylenimine, and 5 wt% 20 nm Al2O3 showed the highest pure water flux, porosity, viscosity, and morphological stability. This membrane may have potential uses in water treatment applications.
Surface coating of polyamide reverse osmosis membranes with zwitterionic 3-(3,4-dihydroxyphenyl)-l-alanine (l-DOPA) for forward osmosis
(WILEY, 111 RIVER ST, HOBOKEN 07030-5774, NJ USA, 2020) Saki, Seda; Uzal, Nigmet; 0000-0002-0912-3459; AGÜ, Mühendislik Fakültesi, İnşaat Mühendisliği Bölümü
To overcome low permeability and fouling problems of membranes used in FO processes, modification is needed to improve the hydrophilicity, permeability and selectivity of membranes. In this work, thin film composite (TFC) commercial polyamide RO membranes (BW30-LE, SW30-HR, AG and AC) were functionalized with zwitterionicl-DOPA. The effect ofl-DOPA on the morphology of membranes was determined via SEM, FT-IR, AFM and contact angle analysis. Thel-DOPA modified BW30-LE membrane showed excellent properties with 46 degrees contact angle and 3.8 L/m(2)hbar water permeability and 0.83 L/m(2)h salt permeability. Although,l-DOPA modified BW30-LE membrane had the highest water flux and hydrophilicity,l-DOPA modified SW30-HR membrane showed higher FO flux with 9.38 L/m(2)h than BW 30 membrane with 3.5 L/m(2)h at 50 g/L NaCl draw solution. Introducing hydroxyl and carboxyl ionic groups on the membrane surface withl-DOPA coating enhanced the FO performance and water permeability which provide a new insight in FO applications.